E120 Lawn Tractor

A 20-hp (14.9-kW) V-twin engine has plenty of power and torque to handle tough mowing, mulching, and bagging conditions:

• V-twin cylinder design for greater torque, lower vibration, and improved sound quality
• Auto choke to allow operators to start the engine without needing the choke unless air temperatures are near or below freezing
• Spring-return feature to ensure the operator will not mistakenly leave the throttle lever in the choke position
• Electronic ignition for fast starts
• Cast-iron cylinder liners for longer engine life
• Overhead valves for excellent power and fuel economy
• Full-pressure lubrication and oil filter for cleaner oil, prolonging engine life and extending the time between oil changes
  • More effective when operating the tractor on an incline
• John Deere Easy Change™ 30-second oil change system makes changing the engine oil easy, quick, and clean.

Fuel tank has gauge to show fuel level from the operator's seat

The fuel tank gauge shows how much fuel is in the tank and can be seen without leaving the operator's seat:

• Easy to check fuel level
• Convenient location

Fuel tank:

• The capacity is 2.4 U.S. gal. (9.1 L).
• The fuel-filler opening is conveniently located under the seat. 
  • Filling the tank without spilling is easy.
  • A tethered fuel tank cap is more convenient.
  • The sealed fuel cap helps keep vapors inside the tank.
  • The tractor has a California Air Resources Board (CARB) certified engine for reduced air pollution.

The John Deere Easy Change 30-second oil change system makes changing the engine oil easy, quick, and clean. Changing the oil is as easy as twisting on a new oil-filled filter. Oil does not need to be drained from the engine.

The John Deere Easy Change filter is an additional engine oil reservoir. Changing the filter removes the captured contaminants and replaces about 0.8 qt (0.76 L) of the engine oil.

The functionality does not stop with ease of use. The Easy Change oil system has several meaningful benefits over the traditional oil filter system of the 100 Series:

• A synthetic filter material is used for more predictable filtering and longer life.
• Filtering capacity is greater than with a standard oil filter.
  • More filter surface area
  • More oil flow capacity
• The system has 40 percent more oil volume.
• The oil and engine run cooler.
• The oil filter valve closes whenever the engine stops, so filtered particles are captured and cannot drain back into the engine.
• The risk of spilling during oil service is greatly reduced.
• Waste oil (and new oil production) is reduced by over 1,000,000 lb (453,592.4 kg) per tractor production year.
• This system is not a compromise to just make oil changes easier—these engines pass the same expectations and rigorous testing as always.

Partly due to these improvements, it is not necessary to remove and dispose of all the oil in the engine during service.

Everyone who uses the John Deere Easy Change system saves time and avoids the mess of a traditional oil change. In the past, many 100 Series Lawn Tractor owners rarely or never got around to changing their engine oil. With John Deere Easy Change, even owners who previously would not consider changing the oil themselves can easily do it. The Easy Change 30-second oil change system is a no-mess, no-fuss solution the competition cannot match.

Installation instructions are in the Operator’s Manual and in the John Deere Easy Change service part box.

Please recycle. Many local government recycling programs, authorized retailers, auto-service centers, and auto-parts stores will puncture and recycle used oil filters and oil.

The solid one-piece frame is constructed of 12-gauge, 0.105-in. (2.66-mm) steel:

• Full-length, robotically-welded frame design has high-strength steel rails for added strength and long life.
• One-piece, steel fender deck is bolted to the frame.

Cast-iron front axle will not bend

The front axle is constructed of solid cast iron that will not bend:

• Automotive-like steering system with sector and pinion steering gears and single drag link with a tie rod provides a very strong, low-effort, and tight-turning system.
• Three grease fittings, on both steering spindles and center pivot, allow for regular lubrication to help maintain easy steering and minimize wear.
• Large, 0.75-in. (1.9-cm) diameter wheel spindles provide excellent durability.

CargO Mount™ system makes installation of rear bagger and other attachments easy

The CargO Mount system is a combination of front- and rear-mounting points providing convenient and easy installation of the sun canopy, rear bagger, and other attachments.

An advantage of lawn tractors is their ability to use equipment for snow removal. Lawn tractor owners can add a John Deere snow blower or front blade to make quick work of moving snow whenever the need arises. Weather enclosure and tire-chain attachments add comfort and performance.

Equipment available for snow removal includes:

• 44-in. (112-cm) Snow Blower
• 46-in. (117-cm) Front Blade
• Tire chains or TerraGrip traction belts
• Weather enclosure
• Weights

 

A Kanzaki® Tuff Torq® hydrostatic transmission gives an infinite choice of speeds and makes changing the direction of travel easy. Side-by-side foot pedals control the speed and direction of travel:

• Automotive-type accelerator controls ensure easy operation.
• Operator can change direction without lifting foot off the platform.
• Large pedal surface gives superior operator comfort.

Appropriate transmissions are used in each model, depending on rear tire size and tractor performance requirements, to ensure excellent performance and reliability:

• Tuff Torq TLT200A - E110, E120, E130
• Tuff Torq TLT200B - E140, E150, E160
• Tuff Torq K46AC - E170, E180

Standard cruise control (E120, E130, E150, E160, E170, and E180)

An easy-to-use cruise control option maintains the tractor's speed for mowing larger areas:

• To engage, lift up on the cruise lever and hold it until the foot is removed from the forward pedal.
• To disengage, lightly press and then release the forward pedal.
• For emergency stops, cruise can be released by pushing on the brake pedal or pushing down on the cruise control lever.

NOTE: Cruise control is available on all models except the E100, E110, and E140.

Kanzaki and Tuff Torq are trademarks of Kanzaki Kokyukoki Manufacturing Company.

The operator station is designed for operator comfort and easy operation:

• Controls are positioned where they are easy to reach and use to control the tractor.
• The steering wheel is positioned and angled to give the operator plenty of room and steering comfort.
• The seat is tilted back at the optimum angle to provide the most comfortable operator position.

Controls are easy to see and use:

• Large, three-spoke steering wheel for greater operator comfort and control
• Ignition switch is on the dash for starting ease

Wide footrest areas with non-slip, anti-vibration floor mats are provided for operator comfort:

• Debris removing channels help keep the footrest area clean and dry
• The wide footrest makes it easier to step over the mower deck while entering or exiting the seat.

The operator seat has a 15-in. (38.1-cm) back height for good support. It is especially helpful when operating the tractor for extended periods of time. It can be easily adjusted forward or rearward while in the seat, with seat travel of 5.5 in. (14 cm) and 10 different positions.

Two long seat springs give plenty of seat travel to smooth out the ride, keeping the operator comfortable while operating the tractor.

The seat can be tilted forward for protection from the elements and to provide easy access to the fuel tank.

A storage compartment and beverage holder, located on the right-side fender, are conveniently located and easy to use.

NOTE: A storage compartment cover is standard on E120, E130, E150, E160, E170 and E180 Tractors and optional on the E110 and E140.

Instruments and controls

The contoured dash has clean, attractive styling:

• Controls are color coded and labeled for easy identification by the operator.
• Controls are logically placed and easy to reach.
• The hour meter makes it easy to tell when oil changes and other maintenance should be performed.
• The service reminder feature will indicate that a general lubrication or mower/engine service interval has been reached.
• When service is required, arrows will periodically flash for two hours.
• Functional design of the controls provides good appearance and a comfortable feel.

Side-by-side transmission control pedals

Side-by-side foot pedals control the speed and direction of travel:

• Automotive-type accelerator controls ensure easy operation.
• Operator can change direction without lifting foot off the platform.
• Large pedal surface gives superior operator comfort.

Cruise control (E120, E130, E150, E160, E170, and E180)

Cruise control is available on the E120, E130, E150, E160, E170, and E180:

• To engage, lift up on the cruise lever and hold until the foot is removed from the forward pedal.
• For emergency stop, the cruise control can be released by pushing on the brake pedal or the forward pedal.

Mower deck height adjustment

A spring-assisted, low-effort lift lever simplifies setting and adjusting the mower cut height:

• Increments of 0.25 in. (0.64 cm) allow for fine-tuning the cut height.
• Cut height is adjustable from 1 in. (2.5 cm) to 4 in. (10.2 cm).

Parking brake control

The parking brake control is conveniently located for easy access. It holds the brake pedal securely in the locked position.

Manual power take-off (PTO)

The mower deck is engaged with an easy-to-see and easy-to-use yellow lever on the dashboard. Its placement on the right side leaves a lot of room on the left, the entry side of the tractor, for the operator to get on and off the tractor.

Reverse implement option (RIO)

Using RIO

CAUTION: Children or bystanders may be injured by rotating blades. Before traveling forward or rearward:

• Carefully check the area around the machine.
• Disengage the mower before backing up.

 

NOTE: Backing up while the mower is engaged is strongly discouraged. RIO should be used only when operating another attachment or when the operator deems it necessary to reposition the machine with the mower engaged.

 

1. Stop forward travel.
2. Look behind the machine to be sure there are no bystanders.
3. Push and hold in the RIO switch while depressing the reverse pedal slightly for a hydrostatic transmission or moving the transmission shift lever to the rear slot (reverse) for a continuously variable transmission (CVT)/automatic transmission.

 

NOTE: If the engine and mower or other attachment stops while repositioning the machine, return the attachment engagement lever/switch to the off position. Start the engine and engage mower or other attachment. Begin again with step 2.

 

4. Release the RIO switch and reposition the machine as the machine begins to move rearward.
5. Resume forward travel. The mower or other attachment should continue operating.
6. Repeat procedure to position the machine again.

The one-piece hood opens easily to permit checking and servicing the engine:

• Important service points are located within easy reach.
• A service-interval decal is provided inside the tractor hood for convenience when servicing the tractor.

The John Deere Easy Change 30-second oil change system makes changing the engine oil easy, quick, and clean. Changing the oil is as easy as removing the old oil-filled filter and twisting on a new oil-filled filter. Oil does not need to be drained from the engine. The removed filter contains the captured contaminants and a portion of the engine oil.

The seat tilts up and out of the way to make adding fuel easy.

The 100 Series Tractors are covered by a 2-year/120-hour bumper-to-bumper warranty*:

• Premium features of 100 Series Tractors allow for this long warranty period.

*Term limited to years or hours used, whichever comes first, and varies by model. See the LIMITED WARRANTY FOR NEW JOHN DEERE TURF AND UTILITY EQUIPMENT at JohnDeere.com or JohnDeere.ca/TUWarranty for details.

Hood will not dent or rust and includes quality headlights for good visibility

The hood is made of molded-in color material:

• Reduces sound
• Will not rust or dent
• Openings on the side of the hood let in plenty of cooling air while keeping the sound level low.
• Two headlights provide good lighting for nighttime operation.

Keep a John Deere riding lawn mower running its best and know how it mows with the John Deere MowerPlus app. Simply scan the lawn tractor’s barcode to get custom information. The app helps determine the best time to mow, communicates expert pre-mow tips, offers maintenance reminders, and provides walk-through guides.

Look for the MowerPlus app on the iOS® or Android™ system app stores.

The app supports residential lawn equipment such as 100 Series, S240, X300, X500, X700, Z200 through Z600, and many similarly-sized older products. It does not presently support tractor models numbered 1000 and larger, such as 1025R.

NOTE: Some product image variation may exist.

 

MowerPlus hour meter connector also available (sold separately)

The John Deere MowerPlus hour meter connector wirelessly links a 100 Series or S240 Lawn Tractor to the MowerPlus app on a mobile device. The hour meter connector transmits engine usage to the app, making it easy to track maintenance intervals:

• iOS version 10 or higher is compatible with the hour meter connector.
• Android versions are not compatible with the hour meter connector at this time.

iOS is a trademark of Cisco Technology, Inc. used under license by Apple Inc. Android is a trademark of Google LLC.

The Edge cutting system has been trademarked to emphasize the advantages of the John Deere mower deck designs. They give the mower superior convenience, performance, and reliability.

The 42-in. (107-cm) two-spindle, three-in-one mower is constructed of 13-gauge, 0.090-in. (2.3-mm) steel for long life:

• The mower deck has a rolled lip to provide greater strength and protection.
• The deep-deck mower design lifts grass for a clean, even cut.
• The smooth underside of the mower prevents grass buildup and evenly disperses grass clippings.
• The rolled outer edge of the deck provides extra strength and protection.
• Dual-stage E-coat and powder paint coatings provide extra protection from rust.
• No tools are required to go from mulching to side discharge to rear bagging.
• The blade-to-spindle design provides a unique mounting system for the mower blade that provides extra safety and convenience.
• A mulch cover is an optional attachment that can be installed without tools to allow mulching with the standard mower blades.   
• A high-performance mulch plug is an optional attachment that includes a mulch plug and special mulching blades for excellent performance.
• A cut-and-throw, 6.5-bu (229-L) rear bagger is sold separately.

Mower wash port

A wash port is provided to make cleaning the underside of the mower deck easy:

• A hose connector is included with mower deck.

StarLock™ blade design

The StarLock blade design keeps the blade bolt at the correct torque for easy removal.

Optional blades for difficult mulching or bagging conditions are available.

Mower deck height adjustment

A spring-assisted, low-effort, ergonomically designed lift lever simplifies setting and adjusting the mower cut height:

• Increments of 0.25 in. (0.64 cm) allow the operator to fine-tune the cut height from 1 in. (2.5 cm) to 4 in. (10.2 cm). 
• The lift handle is shaped and located for easy use, and is out of the way of entering or exiting operators.

An exclusive 2-year or 120-hour (whichever comes first), single-source, bumper-to-bumper warranty* is standard for all John Deere 100 Series Tractors.

• The warranty is hassle free, with one company handling all of the paperwork.
• Premium features of 100 Series Tractors allow for this longer warranty period, with more coverage than comparable tractors.

*Term limited to years or hours used, whichever comes first, and varies by model. See the LIMITED WARRANTY FOR NEW JOHN DEERE TURF AND UTILITY EQUIPMENT at JohnDeere.com or JohnDeere.ca/TUWarranty for details.

Every owner of a John riding lawn and garden product is a potential customer for a high-quality, affordable utility cart. Utility carts can be used to haul a variety of materials including firewood, lawn debris, sand, dirt, mulch, garden tools, plants, and bushes.

Utility carts are designed, painted, and decaled to be compatible with other John Deere equipment.

NOTE: For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak™ or ZTrak™ mower should not exceed 250 lb (113.4 kg). See the appropriate vehicle pages for the weight of the vehicle and the mower deck.

• The cart has a premium molded, high-density polyethylene box construction.
• Compression molding process allows polyethyl­ene to be the optimum thickness in all areas for superior strength and durability.
• Polyethylene body will not rust or dent; it stays looking new longer.
• 0.75-in. (2-cm) x 2-in. (5-cm) stake pockets are molded in to make the addition of side extensions easy.
• Two vertical 0.75-in. (2-cm) molded channels on each side allow easy use of dividers to separate the box into two or three compartments.
• Ribs in the box bottom add strength and prevent the shovel from hitting bolts when emptying the cart.
• Sloped tailgate design makes emptying the box easier; there is no tailgate to loosen or remove.
• Styling is compatible with other John Deere equipment.
• Pneumatic tires provide turf tread for good flotation, shock absorption, and minimal rolling resistance.

Wheels

Wheels are mounted on a solid, one-piece axle for durability.
 
Iron and Oilite® wheel bearings with grease fittings provide lubrication for long life.

The pneumatic tires offer the following:

• Good flotation
• Minimal rolling resistance
• Shock absorption

Sloped tailgate

A sloped tailgate design makes emptying the box easier; there is no tailgate to loosen or remove.

Tractor hitch

A large-diameter hitch pin provides plenty of strength:

• Fast, easy attachment to the tractor hitch
• Spring pin to ensure the pin stays in place

Tilt latch

An easy-to-use, spring-loaded dump latch allows tilting the box for easier unloading. A steep dump angle makes emptying the cart easier.

Model comparison chart

Comparison with similar models

Model	Order through	Box capacity (heaped)	Material thickness	Maximum weight	Vehicle compatibility
7P	Order Zone	7 cu ft (0.20 m3)	High-density polyethylene (HDPE)**	450 lb* (204 kg)	EZtrak, ZTrak, 100 Series, S240, X300 Series, X500 Series, X700 Series
8Y	Order Zone	8 cu ft (0.22 m3)	HDPE**	300 lb* (136 kg) (tow)	100 Series, S240, X300 Series, X500 Series, X700 Series
10P	Order Zone	10 cu ft (0.28 m3)	Polypropylene	650 lb* (295 kg)	EZtrak, ZTrak, 100 Series, S240, X300 Series, X500 Series, X700 Series
13	Order Zone	13 cu ft (0.37 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,000 lb* (454 kg)	100 Series, S240, X300 Series, X500 Series, X700 Series
16YS	Order Zone	17 cu ft (0.48 m3)	Polypropylene	800 lb (363 kg), 350 lb (158 kg) when using swivel feature to dump	100 Series, S240, X300 Series, X500 Series, X700 Series
17P	Order Zone	17 cu ft (0.48 m3)	Polypropylene	1,000 lb* (454 kg)	100 Series, S240, X300 Series, X500 Series, X700 Series
18	Order Zone	18 cu ft (0.51 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,000 lb* (454 kg)	100 Series, S240, X300 Series, X500 Series, X700 Series
21	Order Zone	21 cu ft (0.59 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,000 lb* (454 kg)	X700 Series

*The total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The maximum weight for the 21 Utility Cart is rated at 20 mph (32.2 km/h).

**HDPE is compression molded for optimum thickness in all areas and maximum durability.

Specifications

 

	7P	8Y	10P	13	16YS	17P	18	21
Box capacity
Heaped	7 cu ft (0.20 m3)	8 cu ft (0.22 m3)	10 cu ft (0.28 m3)	13 cu ft (0.37 m3)	17 cu ft (0.48 m3)	17 cu ft (0.48 m3)	18 cu ft (0.51 m3)	21 cu ft (0.59 m3)
Struck	5.6 cu ft (0.16 m3)	6.6 cu ft (0.19 m3)	8.3 cu ft (0.24 m3)	10 cu ft (0.28 m3)	15 cu ft (0.42 m3)	14 cu ft (0.40 m3)	15 cu ft (0.42 m3)	15 cu ft (0.42 m3)
Maximum weight	450 lb* (204 kg)	300 lb* (136 kg)	650 lb* (295 kg)	1,000 lb* (454 kg)	800 lb* (363 kg), 350 lb (158 kg) when using swivel feature to dump	1,000 lb* (454 kg)	1,000 lb* (454 kg)	1,000 lb* (454 kg)
Box dimensions
Width	33 in. (84 cm)	33.68 in. (85.5 cm)	30.3 in. (77 cm)	30.25 in. (76.8 cm)	39.5 in. (100.3 cm)	39.5 in. (100.3 cm)	38 in. (96.5 cm)	48 in. (122 cm)
Length	45 in. (114 cm)	45 in. (114 cm)	44.5 in. (113 cm)	48 in. (122 cm)	58.5 in. (148.6 cm)	58.5 in. (148.6 cm)	48 in. (122 cm)	48 in. (122 cm)
Depth	10.5 in. (27 cm)	10.75 in. (27.3cm)	12 in. (30.5 cm)	12 in. (30.5 cm)	15.5 in. (39.4 cm)	15.5 in. (39.4 cm)	18 in. (45.7 cm)	11 in. (27.9 cm)
Box construction	Molded	Molded	Molded	Welded	Molded	Molded	Welded	Bolted
Material	High-density polyethylene (HDPE)**	HDPE** w/UV inhibitor	Polypropylene	16-gauge, 0.06-in. (1.5-mm) steel	Polypropylene	Polypropylene	16-gauge, 0.06-in. (1.5-mm) steel	16-gauge, 0.06-in. (1.5-mm) steel
Tailgate	None, sloped	None, sloped	None, sloped	Hinged	None, sloped	None, sloped	Hinged	Lift-out/swing-out
Pneumatic tires	2 ply	---	2 ply	2 ply	4 ply	4 ply	4 ply	2 ply
Size	13x4-6	13x4-6	15x6.00-6	15x6.00-6	16x6.50-8	16x6.50-8	16x6.50-8	20x10.00-8
Tread design	Turf	Knobby	Turf	Turf	Turf	Turf	Turf	Turf
Recommended inflation pressure	30 psi (207 kPa)	30 psi (207 kPa)	14 psi (97 kPa)	14 psi (97 kPa)	35 psi (241 kPa)	28 psi (193 kPa)	28 psi (193 kPa)	10 psi (70 kPa)
Wheel bearings	Iron/Oilite	None	Iron/Oilite	Iron/Oilite	Iron/Oilite	Iron/Oilite	Iron/Oilite	Ball bearings, double sealed
Grease fittings on wheels	Yes	None	Yes	Yes	Yes	Yes	Yes	None
Axle diameter	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	1 in. (2.54 cm)	1 in. (2.54 cm)
Ground clearance	5.62 in. (14.3 cm)	5.25 in. (13.3 cm)	6.5 in. (16.5 cm)	6.5 in. (16.5 cm)	14.25 in. (36.2 cm)	14.25 in. (36.2 cm)	7 in. (17.8 cm)	8.25 in. (21 cm)
Width, overall	34 in. (86.4 cm)	33.68 in. (85.5 cm)	38 in. (96.5 cm)	38 in. (96.5 cm)	39.5 in. (100.3 cm)	39.5 in. (100.3 cm)	38 in. (96.5 cm)	48 in. (122 cm)
Hitch pin	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip
Dump angles	55 degrees	55 degrees	56 degrees	31 degrees	46 degrees	46 degrees	35/40 degrees	35/40 degrees
Maximum tongue weight	100 lb (45.4 kg)	100 lb (45.4 kg)	70 lb (31.75 kg)	100 lb (45.4 kg)	50 lb (22 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)
Shipping weight with carton	68 lb (31 kg)	65 lb (29.5 kg)	79 lb (35.8 kg)	110 lb (49.9 kg)	---	105 lb (47.6 kg)	170 lb (77.1 kg)	240 lb (109 kg)
Net weight	65 lb (29 kg)	55 lb (25 kg)	72 lb (32.7 kg)	105 lb (47.6 kg)	103 lb (47 kg)	105 lb (47.6 kg)	150 lb (68 kg)	220 lb (99.8 kg)

*Total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg).

**HDPE is compression molded for optimum thickness in all areas and maximum durability.

Tractor compatibility and requirements

Utility Carts

Chart below shows vehicle compatibility.

An X indicates cart can be used with the pulling unit.

NOTE: For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The chart shows which utility carts are compatible with the vehicle.

 

	7P	8Y	10P	13	16YS	17P	18	21
EZtrak Z225, Z235, Z245, Z255, Z425, Z435, Z445, Z465, Z625, Z645, Z655, Z665 ZTrak Z335E, Z355E, Z335M, Z345M, Z345R, Z355R, Z375R, Z525E, Z535M, Z540M, Z535R, Z540R, Z720E, Z735E, Z730M, Z735M, Z740R	X		X
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D125, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180	X	X	X	X	X	X	X
S240	X	X	X	X	X	X	X
LT150, LT160, LT180, LT190, LTR180	X	X	X		X	X
LX280, LX280AWS, LX289	X	X	X		X	X
X300, X300R, X304, X310, X320, X324, X340, X360, X330, X350, X350R, X354, X370, X380, X384, X390, X394	X	X	X	X	X	X	X
SST15, SST16, SST18	X	X	X
G110	X	X	X	X	X	X
GT235, GT245	X	X	X	X	X	X
GX255, GX335, GX345, GX355	X	X	X	X	X	X
X500, X520, X530, X534, X540 X570, X580, X584, X590	X	X	X	X	X	X	X
X465, X475, X485, X495, X575, X585, X595	X	X	X	X	X	X	X	X
X700, X720, X724, X728, X729, X740, X744, X748, X749 X710, X730, X734, X738, X739, X750, X754, X758	X	X	X	X	X	X	X	X

For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). See the appropriate vehicle pages for the weight of the vehicle and the mower deck. Additional weight can be added to the vehicle by the following methods:

  

Tractor	Additional weight
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180	Two 30-lb (14-kg) wheel weights, front Two 42-lb (19-kg) suitcase weights, rear
S240	Two 34-lb (15-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, rear
LT150, LT160, LT180, LT190, LTR180	Two 34-lb (15-kg) wheel weights, front Two 31-lb (14.1-kg) plastic shell wheel weights, rear (not for LT190)
LX280, LX280AWS, LX289 X300, X300R, X304, X310, X320, X324, X340, X360 X330, X350, X350R, X354, X370, X380, X384, X390, X394	Two 34-lb (15-kg) wheel weights, front Four 42-lb (19-kg) suitcase weights, rear
SST15, SST16, SST18	One 88-lb (40-kg) weight kit, front Three 40-lb (18-kg) weights, rear
G100	Two 50-lb (23-kg) wheel weights, rear Two 42-lb (19-kg) suitcase weights, rear
G110	Two 50-lb (23-kg) plastic shell rear wheel weights
GT235, GT245	Two 30-lb (14-kg) wheel weights, front Four 42-lb (19-kg) suitcase weights, front Four 42-lb (19-kg) suitcase weights, rear Four 50-lb (23-kg) wheel weights, rear Two 50-lb (23-kg) plastic shell wheel weights, rear
GX255, GX335, GX345, GX355 X500, X520, X530, X534, X540 X570, X580, X584, X590	Two 30-lb (14-kg) wheel weights, front Four 42-lb (19-kg) suitcase weights, front Four 42-lb (19-kg) suitcase weights, rear Four 50-lb (23-kg) wheel weights, rear Two 50-lb (23-kg) wheel plastic shell weights, rear
X465, X475, X485, X495, X575, X585, X595 X700, X720, X724, X728, X729, X740, X744, X748, X749 X710, X730, X734, X738, X739, X750, X754, X758	Four 42-lb (19-kg) suitcase weights, front Two 70-lb (32-kg) wheel cast-iron starter weights, rear Four 50-lb (23-kg) cast-iron wheel weights, rear Two 50-lb (23-kg) plastic shell wheel weights, rear Six 42-lb (19-kg) suitcase weights, rear

Ordering information

Please contact a local John Deere dealer for availability and pricing information.

7P Poly Utility Cart
Order number: LP21935

Oilite is a trademark of Beemer Precision, Incorporated.

The 8-cu-ft (0.23-m³), 300-lb (136-kg) capacity 8Y Convertible Poly Utility Cart can be used to haul a variety of materials including lawn debris, sand, dirt, mulch, and plants. The unique convertible hitch allows changing the cart from tow-behind mode to push mode without tools.

Key features include:

• Compatible with riding lawn tractors and garden tractors
• Durable poly construction
• All-terrain pneumatic tires
• Converts from tow cart to push cart without tools
• Large handle is provided for ease of use

Every owner of a John Deere riding lawn and garden product is a potential customer for a high-quality, affordable utility cart. Utility carts can be used to haul a variety of materials including firewood, lawn debris, sand, dirt, mulch, garden tools, plants, and bushes. Utility carts are designed, painted, and decaled to be compatible with other John Deere equipment.
 
NOTE: For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. See the appropriate vehicle pages for the weight of the vehicle and the mower deck. 

Model comparison chart

Comparison with similar models

Model	Order through	Box capacity (heaped)	Material thickness	Maximum weight	Vehicle compatibility
7P	Order Zone	7 cu ft (0.20 m3)	High-density polyethylene (HDPE)**	450 lb* (204 kg)	EZtrak™, ZTrak™, 100 Series, S240, X300 Series, X500 Series, X700 Series
8Y	Order Zone	8 cu ft (0.22 m3)	HDPE**	300 lb* (136 kg) (tow)	100 Series, S240, X300 Series, X500 Series, X700 Series
10P	Order Zone	10 cu ft (0.28 m3)	Polypropylene	650 lb* (295 kg)	EZtrak, ZTrak, 100 Series, S240, X300 Series, X500 Series, X700 Series
13	Order Zone	13 cu ft (0.37 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,000 lb* (454 kg)	100 Series, S240, X300 Series, X500 Series, X700 Series
16YS	Order Zone	17 cu ft (0.48 m3)	Polypropylene	800 lb (363 kg), 350 lb (158 kg) when using swivel feature to dump	100 Series, S240, X300 Series, X500 Series, X700 Series
17P	Order Zone	17 cu ft (0.48 m3)	Polypropylene	1,000 lb* (454 kg)	100 Series, S240, X300 Series, X500 Series, X700 Series
18	Order Zone	18 cu ft (0.51 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,000 lb* (454 kg)	100 Series, S240, X300 Series, X500 Series, X700 Series
21	Order Zone	21 cu ft (0.59 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,000 lb* (454 kg)	X700 Series

*The total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The maximum weight for the 21 Utility Cart is rated at 20 mph (32.2 km/h).

**HDPE is compression molded for optimum thickness in all areas and maximum durability.

Specifications

 

	7P	8Y	10P	13	16YS	17P	18	21
Box capacity
Heaped	7 cu ft (0.20 m3)	8 cu ft (0.22 m3)	10 cu ft (0.28 m3)	13 cu ft (0.37 m3)	17 cu ft (0.48 m3)	17 cu ft (0.48 m3)	18 cu ft (0.51 m3)	21 cu ft (0.59 m3)
Struck	5.6 cu ft (0.16 m3)	6.6 cu ft (0.19 m3)	8.3 cu ft (0.24 m3)	10 cu ft (0.28 m3)	15 cu ft (0.42 m3)	14 cu ft (0.40 m3)	15 cu ft (0.42 m3)	15 cu ft (0.42 m3)
Maximum weight	450 lb* (204 kg)	300 lb* (136 kg)	650 lb* (295 kg)	1,000 lb* (454 kg)	800 lb* (363 kg), 350 lb (158 kg) when using swivel feature to dump	1,000 lb* (454 kg)	1,000 lb* (454 kg)	1,000 lb* (454 kg)
Box dimensions
Width	33 in. (84 cm)	33.68 in. (85.5 cm)	30.3 in. (77 cm)	30.25 in. (76.8 cm)	39.5 in. (100.3 cm)	39.5 in. (100.3 cm)	38 in. (96.5 cm)	48 in. (122 cm)
Length	45 in. (114 cm)	45 in. (114 cm)	44.5 in. (113 cm)	48 in. (122 cm)	58.5 in. (148.6 cm)	58.5 in. (148.6 cm)	48 in. (122 cm)	48 in. (122 cm)
Depth	10.5 in. (27 cm)	10.75 in. (27.3cm)	12 in. (30.5 cm)	12 in. (30.5 cm)	15.5 in. (39.4 cm)	15.5 in. (39.4 cm)	18 in. (45.7 cm)	11 in. (27.9 cm)
Box construction	Molded	Molded	Molded	Welded	Molded	Molded	Welded	Bolted
Material	High-density polyethylene (HDPE)**	HDPE** w/UV inhibitor	Polypropylene	16-gauge, 0.06-in. (1.5-mm) steel	Polypropylene	Polypropylene	16-gauge, 0.06-in. (1.5-mm) steel	16-gauge, 0.06-in. (1.5-mm) steel
Tailgate	None, sloped	None, sloped	None, sloped	Hinged	None, sloped	None, sloped	Hinged	Lift-out/swing-out
Pneumatic tires	2 ply	---	2 ply	2 ply	4 ply	4 ply	4 ply	2 ply
Size	13x4-6	13x4-6	15x6.00-6	15x6.00-6	16x6.50-8	16x6.50-8	16x6.50-8	20x10.00-8
Tread design	Turf	Knobby	Turf	Turf	Turf	Turf	Turf	Turf
Recommended inflation pressure	30 psi (207 kPa)	30 psi (207 kPa)	14 psi (97 kPa)	14 psi (97 kPa)	35 psi (241 kPa)	28 psi (193 kPa)	28 psi (193 kPa)	10 psi (70 kPa)
Wheel bearings	Iron/Oilite	None	Iron/Oilite	Iron/Oilite	Iron/Oilite	Iron/Oilite	Iron/Oilite	Ball bearings, double sealed
Grease fittings on wheels	Yes	None	Yes	Yes	Yes	Yes	Yes	None
Axle diameter	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	1 in. (2.54 cm)	1 in. (2.54 cm)
Ground clearance	5.62 in. (14.3 cm)	5.25 in. (13.3 cm)	6.5 in. (16.5 cm)	6.5 in. (16.5 cm)	14.25 in. (36.2 cm)	14.25 in. (36.2 cm)	7 in. (17.8 cm)	8.25 in. (21 cm)
Width, overall	34 in. (86.4 cm)	33.68 in. (85.5 cm)	38 in. (96.5 cm)	38 in. (96.5 cm)	39.5 in. (100.3 cm)	39.5 in. (100.3 cm)	38 in. (96.5 cm)	48 in. (122 cm)
Hitch pin	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip
Dump angles	55 degrees	55 degrees	56 degrees	31 degrees	46 degrees	46 degrees	35/40 degrees	35/40 degrees
Maximum tongue weight	100 lb (45.4 kg)	100 lb (45.4 kg)	70 lb (31.75 kg)	100 lb (45.4 kg)	50 lb (22 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)
Shipping weight with carton	68 lb (31 kg)	65 lb (29.5 kg)	79 lb (35.8 kg)	110 lb (49.9 kg)	---	105 lb (47.6 kg)	170 lb (77.1 kg)	240 lb (109 kg)
Net weight	65 lb (29 kg)	55 lb (25 kg)	72 lb (32.7 kg)	105 lb (47.6 kg)	103 lb (47 kg)	105 lb (47.6 kg)	150 lb (68 kg)	220 lb (99.8 kg)

*Total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg).

**HDPE is compression molded for optimum thickness in all areas and maximum durability.

Tractor compatibility and requirements

Utility Carts

Chart below shows vehicle compatibility.

An X indicates cart can be used with the pulling unit.

NOTE: For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The chart shows which utility carts are compatible with the vehicle.

 

	7P	8Y	10P	13	16YS	17P	18	21
EZtrak Z225, Z235, Z245, Z255, Z425, Z435, Z445, Z465, Z625, Z645, Z655, Z665 ZTrak Z335E, Z355E, Z335M, Z345M, Z345R, Z355R, Z375R, Z525E, Z535M, Z540M, Z535R, Z540R, Z720E, Z735E, Z730M, Z735M, Z740R	X		X
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D125, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180	X	X	X	X	X	X	X
S240	X	X	X	X	X	X	X
LT150, LT160, LT180, LT190, LTR180	X	X	X		X	X
LX280, LX280AWS, LX289	X	X	X		X	X
X300, X300R, X304, X310, X320, X324, X340, X360, X330, X350, X350R, X354, X370, X380, X384, X390, X394	X	X	X	X	X	X	X
SST15, SST16, SST18	X	X	X
G110	X	X	X	X	X	X
GT235, GT245	X	X	X	X	X	X
GX255, GX335, GX345, GX355	X	X	X	X	X	X
X500, X520, X530, X534, X540 X570, X580, X584, X590	X	X	X	X	X	X	X
X465, X475, X485, X495, X575, X585, X595	X	X	X	X	X	X	X	X
X700, X720, X724, X728, X729, X740, X744, X748, X749 X710, X730, X734, X738, X739, X750, X754, X758	X	X	X	X	X	X	X	X

For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). See the appropriate vehicle pages for the weight of the vehicle and the mower deck. Additional weight can be added to the vehicle by the following methods:

  

Tractor	Additional weight
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180	Two 30-lb (14-kg) wheel weights, front Two 42-lb (19-kg) suitcase weights, rear
S240	Two 34-lb (15-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, rear
LT150, LT160, LT180, LT190, LTR180	Two 34-lb (15-kg) wheel weights, front Two 31-lb (14.1-kg) plastic shell wheel weights, rear (not for LT190)
LX280, LX280AWS, LX289 X300, X300R, X304, X310, X320, X324, X340, X360 X330, X350, X350R, X354, X370, X380, X384, X390, X394	Two 34-lb (15-kg) wheel weights, front Four 42-lb (19-kg) suitcase weights, rear
SST15, SST16, SST18	One 88-lb (40-kg) weight kit, front Three 40-lb (18-kg) weights, rear
G100	Two 50-lb (23-kg) wheel weights, rear Two 42-lb (19-kg) suitcase weights, rear
G110	Two 50-lb (23-kg) plastic shell rear wheel weights
GT235, GT245	Two 30-lb (14-kg) wheel weights, front Four 42-lb (19-kg) suitcase weights, front Four 42-lb (19-kg) suitcase weights, rear Four 50-lb (23-kg) wheel weights, rear Two 50-lb (23-kg) plastic shell wheel weights, rear
GX255, GX335, GX345, GX355 X500, X520, X530, X534, X540 X570, X580, X584, X590	Two 30-lb (14-kg) wheel weights, front Four 42-lb (19-kg) suitcase weights, front Four 42-lb (19-kg) suitcase weights, rear Four 50-lb (23-kg) wheel weights, rear Two 50-lb (23-kg) wheel plastic shell weights, rear
X465, X475, X485, X495, X575, X585, X595 X700, X720, X724, X728, X729, X740, X744, X748, X749 X710, X730, X734, X738, X739, X750, X754, X758	Four 42-lb (19-kg) suitcase weights, front Two 70-lb (32-kg) wheel cast-iron starter weights, rear Four 50-lb (23-kg) cast-iron wheel weights, rear Two 50-lb (23-kg) plastic shell wheel weights, rear Six 42-lb (19-kg) suitcase weights, rear

Ordering information

Please contact a local John Deere dealer for availability and pricing information.

8Y Convertible Poly Utility Cart
Order number: LP22755

Oilite is a trademark of Beemer Precision, Incorporated.

Every owner of a John Deere riding lawn and garden product is a potential customer for a high-quality, affordable utility cart.

Utility carts can be used to haul a variety of materials:

• Firewood
• Lawn debris
• Sand
• Dirt
• Mulch
• Garden tools
• Plants and bushes

The 10P Utility Cart is designed, painted, and decaled to be compatible with other John Deere equipment:

• Large 650-lb (295-kg) capacity
• 10-cu ft (283-L), heavy-duty, 0.25-in. (6.4-mm) thick poly bed
• Will not dent or rust
• 15x6 tubeless pneumatic tires with turf tread for maximum traction
• Easy, hands-free foot pedal dump release
• Steep dump angle for complete emptying

 

A convenient foot pedal dump release kit, LP48017, which now comes standard on all 10P and 17P carts is available to retrofit existing poly carts. This kit allows the operator to use both hands to lift the cart bed for more natural and efficient unloading.

 

Model comparison chart

Comparison with similar models

Model	Order through	Box capacity (heaped)	Material thickness	Maximum weight	Vehicle compatibility
7P	Order Zone	7 cu ft (0.20 m3)	High-density polyethylene (HDPE)**	450 lb* (204 kg)	EZtrak™, ZTrak™, 100 Series, S240, X300 Series, X500 Series, X700 Series
8Y	Order Zone	8 cu ft (0.22 m3)	HDPE**	300 lb* (136 kg) (tow)	100 Series, S240, X300 Series, X500 Series, X700 Series
10P	Order Zone	10 cu ft (0.28 m3)	Polypropylene	650 lb* (295 kg)	EZtrak, ZTrak, 100 Series, S240, X300 Series, X500 Series, X700 Series
13	Order Zone	13 cu ft (0.37 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,000 lb* (454 kg)	100 Series, S240, X300 Series, X500 Series, X700 Series
16YS	Order Zone	17 cu ft (0.48 m3)	Polypropylene	800 lb (363 kg), 350 lb (158 kg) when using swivel feature to dump	100 Series, S240, X300 Series, X500 Series, X700 Series
17P	Order Zone	17 cu ft (0.48 m3)	Polypropylene	1,000 lb* (454 kg)	100 Series, S240, X300 Series, X500 Series, X700 Series
18	Order Zone	18 cu ft (0.51 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,000 lb* (454 kg)	100 Series, S240, X300 Series, X500 Series, X700 Series
21	Order Zone	21 cu ft (0.59 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,000 lb* (454 kg)	X700 Series

*The total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The maximum weight for the 21 Utility Cart is rated at 20 mph (32.2 km/h).

**HDPE is compression molded for optimum thickness in all areas and maximum durability.

Specifications

 

	7P	8Y	10P	13	16YS	17P	18	21
Box capacity
Heaped	7 cu ft (0.20 m3)	8 cu ft (0.22 m3)	10 cu ft (0.28 m3)	13 cu ft (0.37 m3)	17 cu ft (0.48 m3)	17 cu ft (0.48 m3)	18 cu ft (0.51 m3)	21 cu ft (0.59 m3)
Struck	5.6 cu ft (0.16 m3)	6.6 cu ft (0.19 m3)	8.3 cu ft (0.24 m3)	10 cu ft (0.28 m3)	15 cu ft (0.42 m3)	14 cu ft (0.40 m3)	15 cu ft (0.42 m3)	15 cu ft (0.42 m3)
Maximum weight	450 lb* (204 kg)	300 lb* (136 kg)	650 lb* (295 kg)	1,000 lb* (454 kg)	800 lb* (363 kg), 350 lb (158 kg) when using swivel feature to dump	1,000 lb* (454 kg)	1,000 lb* (454 kg)	1,000 lb* (454 kg)
Box dimensions
Width	33 in. (84 cm)	33.68 in. (85.5 cm)	30.3 in. (77 cm)	30.25 in. (76.8 cm)	39.5 in. (100.3 cm)	39.5 in. (100.3 cm)	38 in. (96.5 cm)	48 in. (122 cm)
Length	45 in. (114 cm)	45 in. (114 cm)	44.5 in. (113 cm)	48 in. (122 cm)	58.5 in. (148.6 cm)	58.5 in. (148.6 cm)	48 in. (122 cm)	48 in. (122 cm)
Depth	10.5 in. (27 cm)	10.75 in. (27.3cm)	12 in. (30.5 cm)	12 in. (30.5 cm)	15.5 in. (39.4 cm)	15.5 in. (39.4 cm)	18 in. (45.7 cm)	11 in. (27.9 cm)
Box construction	Molded	Molded	Molded	Welded	Molded	Molded	Welded	Bolted
Material	High-density polyethylene (HDPE)**	HDPE** w/UV inhibitor	Polypropylene	16-gauge, 0.06-in. (1.5-mm) steel	Polypropylene	Polypropylene	16-gauge, 0.06-in. (1.5-mm) steel	16-gauge, 0.06-in. (1.5-mm) steel
Tailgate	None, sloped	None, sloped	None, sloped	Hinged	None, sloped	None, sloped	Hinged	Lift-out/swing-out
Pneumatic tires	2 ply	---	2 ply	2 ply	4 ply	4 ply	4 ply	2 ply
Size	13x4-6	13x4-6	15x6.00-6	15x6.00-6	16x6.50-8	16x6.50-8	16x6.50-8	20x10.00-8
Tread design	Turf	Knobby	Turf	Turf	Turf	Turf	Turf	Turf
Recommended inflation pressure	30 psi (207 kPa)	30 psi (207 kPa)	14 psi (97 kPa)	14 psi (97 kPa)	35 psi (241 kPa)	28 psi (193 kPa)	28 psi (193 kPa)	10 psi (70 kPa)
Wheel bearings	Iron/Oilite	None	Iron/Oilite	Iron/Oilite	Iron/Oilite	Iron/Oilite	Iron/Oilite	Ball bearings, double sealed
Grease fittings on wheels	Yes	None	Yes	Yes	Yes	Yes	Yes	None
Axle diameter	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	1 in. (2.54 cm)	1 in. (2.54 cm)
Ground clearance	5.62 in. (14.3 cm)	5.25 in. (13.3 cm)	6.5 in. (16.5 cm)	6.5 in. (16.5 cm)	14.25 in. (36.2 cm)	14.25 in. (36.2 cm)	7 in. (17.8 cm)	8.25 in. (21 cm)
Width, overall	34 in. (86.4 cm)	33.68 in. (85.5 cm)	38 in. (96.5 cm)	38 in. (96.5 cm)	39.5 in. (100.3 cm)	39.5 in. (100.3 cm)	38 in. (96.5 cm)	48 in. (122 cm)
Hitch pin	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip
Dump angles	55 degrees	55 degrees	56 degrees	31 degrees	46 degrees	46 degrees	35/40 degrees	35/40 degrees
Maximum tongue weight	100 lb (45.4 kg)	100 lb (45.4 kg)	70 lb (31.75 kg)	100 lb (45.4 kg)	50 lb (22 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)
Shipping weight with carton	68 lb (31 kg)	65 lb (29.5 kg)	79 lb (35.8 kg)	110 lb (49.9 kg)	---	105 lb (47.6 kg)	170 lb (77.1 kg)	240 lb (109 kg)
Net weight	65 lb (29 kg)	55 lb (25 kg)	72 lb (32.7 kg)	105 lb (47.6 kg)	103 lb (47 kg)	105 lb (47.6 kg)	150 lb (68 kg)	220 lb (99.8 kg)

*Total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg).

**HDPE is compression molded for optimum thickness in all areas and maximum durability.

Tractor compatibility and requirements

Utility Carts

Chart below shows vehicle compatibility.

An X indicates cart can be used with the pulling unit.

NOTE: For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The chart shows which utility carts are compatible with the vehicle.

 

	7P	8Y	10P	13	16YS	17P	18	21
EZtrak Z225, Z235, Z245, Z255, Z425, Z435, Z445, Z465, Z625, Z645, Z655, Z665 ZTrak Z335E, Z355E, Z335M, Z345M, Z345R, Z355R, Z375R, Z525E, Z535M, Z540M, Z535R, Z540R, Z720E, Z735E, Z730M, Z735M, Z740R	X		X
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D125, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180	X	X	X	X	X	X	X
S240	X	X	X	X	X	X	X
LT150, LT160, LT180, LT190, LTR180	X	X	X		X	X
LX280, LX280AWS, LX289	X	X	X		X	X
X300, X300R, X304, X310, X320, X324, X340, X360, X330, X350, X350R, X354, X370, X380, X384, X390, X394	X	X	X	X	X	X	X
SST15, SST16, SST18	X	X	X
G110	X	X	X	X	X	X
GT235, GT245	X	X	X	X	X	X
GX255, GX335, GX345, GX355	X	X	X	X	X	X
X500, X520, X530, X534, X540 X570, X580, X584, X590	X	X	X	X	X	X	X
X465, X475, X485, X495, X575, X585, X595	X	X	X	X	X	X	X	X
X700, X720, X724, X728, X729, X740, X744, X748, X749 X710, X730, X734, X738, X739, X750, X754, X758	X	X	X	X	X	X	X	X

For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). See the appropriate vehicle pages for the weight of the vehicle and the mower deck. Additional weight can be added to the vehicle by the following methods:

  

Tractor	Additional weight
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180	Two 30-lb (14-kg) wheel weights, front Two 42-lb (19-kg) suitcase weights, rear
S240	Two 34-lb (15-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, rear
LT150, LT160, LT180, LT190, LTR180	Two 34-lb (15-kg) wheel weights, front Two 31-lb (14.1-kg) plastic shell wheel weights, rear (not for LT190)
LX280, LX280AWS, LX289 X300, X300R, X304, X310, X320, X324, X340, X360 X330, X350, X350R, X354, X370, X380, X384, X390, X394	Two 34-lb (15-kg) wheel weights, front Four 42-lb (19-kg) suitcase weights, rear
SST15, SST16, SST18	One 88-lb (40-kg) weight kit, front Three 40-lb (18-kg) weights, rear
G100	Two 50-lb (23-kg) wheel weights, rear Two 42-lb (19-kg) suitcase weights, rear
G110	Two 50-lb (23-kg) plastic shell rear wheel weights
GT235, GT245	Two 30-lb (14-kg) wheel weights, front Four 42-lb (19-kg) suitcase weights, front Four 42-lb (19-kg) suitcase weights, rear Four 50-lb (23-kg) wheel weights, rear Two 50-lb (23-kg) plastic shell wheel weights, rear
GX255, GX335, GX345, GX355 X500, X520, X530, X534, X540 X570, X580, X584, X590	Two 30-lb (14-kg) wheel weights, front Four 42-lb (19-kg) suitcase weights, front Four 42-lb (19-kg) suitcase weights, rear Four 50-lb (23-kg) wheel weights, rear Two 50-lb (23-kg) wheel plastic shell weights, rear
X465, X475, X485, X495, X575, X585, X595 X700, X720, X724, X728, X729, X740, X744, X748, X749 X710, X730, X734, X738, X739, X750, X754, X758	Four 42-lb (19-kg) suitcase weights, front Two 70-lb (32-kg) wheel cast-iron starter weights, rear Four 50-lb (23-kg) cast-iron wheel weights, rear Two 50-lb (23-kg) plastic shell wheel weights, rear Six 42-lb (19-kg) suitcase weights, rear

Ordering information
Please contact a local John Deere dealer for availability and pricing information.

10P Poly Utility Cart
Order number: LPPCT10JD

Oilite is a trademark of Beemer Precision, Incorporated.

Every owner of a John Deere riding lawn and garden product is a potential customer for a high-quality, affordable utility cart. Utility carts can be used to haul a variety of materials, including firewood, lawn debris, dirt, sand, mulch, garden tools, plants, and bushes.

Utility carts are designed, painted, and decaled to be compatible with other John Deere equipment.

For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. See the appropriate vehicle pages for the weight of the vehicle and the mower deck.

Welded box construction provides maximum reliability:

• Requires less setup time than the bolted construction.
• Box sides and bottom are one piece and have rounded corners and no hardware for easy cleaning.

Wheels and tires

Wheels are mounted on a solid, one-piece axle for durability.

Iron/Oilite® wheel bearings with grease fittings provide lubrication for long life.

Pneumatic tires offer:

• Good flotation
• Minimal rolling resistance
• Shock absorption

Turf-tread tires are used on the 13 Utility Cart.

Deluxe tailgate is hinged for easy emptying and can also be quickly removed without the use of tools.

Easy hookup and tilt-dump latch

A large-diameter hitch pin provides plenty of strength:

• Fast, easy attachment to the tractor hitch
• Spring pin to ensure the pin stays in place

The easy-to-use latch allows tilting the bed for easier unloading:

• Steep dump angle makes emptying easier.

Model comparison chart

Comparison with similar models

Model	Order through	Box capacity (heaped)	Material thickness	Maximum weight	Vehicle compatibility
7P	Order Zone	7 cu ft (0.20 m3)	High-density polyethylene (HDPE)**	450 lb* (204 kg)	EZtrak™, ZTrak™, 100 Series, S240, X300 Series, X500 Series, X700 Series
8Y	Order Zone	8 cu ft (0.22 m3)	HDPE**	300 lb* (136 kg) (tow)	100 Series, S240, X300 Series, X500 Series, X700 Series
10P	Order Zone	10 cu ft (0.28 m3)	Polypropylene	650 lb* (295 kg)	EZtrak, ZTrak, 100 Series, S240, X300 Series, X500 Series, X700 Series
13	Order Zone	13 cu ft (0.37 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,000 lb* (454 kg)	100 Series, S240, X300 Series, X500 Series, X700 Series
16YS	Order Zone	17 cu ft (0.48 m3)	Polypropylene	800 lb (363 kg), 350 lb (158 kg) when using swivel feature to dump	100 Series, S240, X300 Series, X500 Series, X700 Series
17P	Order Zone	17 cu ft (0.48 m3)	Polypropylene	1,000 lb* (454 kg)	100 Series, S240, X300 Series, X500 Series, X700 Series
18	Order Zone	18 cu ft (0.51 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,000 lb* (454 kg)	100 Series, S240, X300 Series, X500 Series, X700 Series
21	Order Zone	21 cu ft (0.59 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,000 lb* (454 kg)	X700 Series

*The total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The maximum weight for the 21 Utility Cart is rated at 20 mph (32.2 km/h).

**HDPE is compression molded for optimum thickness in all areas and maximum durability.

Specifications

 

	7P	8Y	10P	13	16YS	17P	18	21
Box capacity
Heaped	7 cu ft (0.20 m3)	8 cu ft (0.22 m3)	10 cu ft (0.28 m3)	13 cu ft (0.37 m3)	17 cu ft (0.48 m3)	17 cu ft (0.48 m3)	18 cu ft (0.51 m3)	21 cu ft (0.59 m3)
Struck	5.6 cu ft (0.16 m3)	6.6 cu ft (0.19 m3)	8.3 cu ft (0.24 m3)	10 cu ft (0.28 m3)	15 cu ft (0.42 m3)	14 cu ft (0.40 m3)	15 cu ft (0.42 m3)	15 cu ft (0.42 m3)
Maximum weight	450 lb* (204 kg)	300 lb* (136 kg)	650 lb* (295 kg)	1,000 lb* (454 kg)	800 lb* (363 kg), 350 lb (158 kg) when using swivel feature to dump	1,000 lb* (454 kg)	1,000 lb* (454 kg)	1,000 lb* (454 kg)
Box dimensions
Width	33 in. (84 cm)	33.68 in. (85.5 cm)	30.3 in. (77 cm)	30.25 in. (76.8 cm)	39.5 in. (100.3 cm)	39.5 in. (100.3 cm)	38 in. (96.5 cm)	48 in. (122 cm)
Length	45 in. (114 cm)	45 in. (114 cm)	44.5 in. (113 cm)	48 in. (122 cm)	58.5 in. (148.6 cm)	58.5 in. (148.6 cm)	48 in. (122 cm)	48 in. (122 cm)
Depth	10.5 in. (27 cm)	10.75 in. (27.3cm)	12 in. (30.5 cm)	12 in. (30.5 cm)	15.5 in. (39.4 cm)	15.5 in. (39.4 cm)	18 in. (45.7 cm)	11 in. (27.9 cm)
Box construction	Molded	Molded	Molded	Welded	Molded	Molded	Welded	Bolted
Material	High-density polyethylene (HDPE)**	HDPE** w/UV inhibitor	Polypropylene	16-gauge, 0.06-in. (1.5-mm) steel	Polypropylene	Polypropylene	16-gauge, 0.06-in. (1.5-mm) steel	16-gauge, 0.06-in. (1.5-mm) steel
Tailgate	None, sloped	None, sloped	None, sloped	Hinged	None, sloped	None, sloped	Hinged	Lift-out/swing-out
Pneumatic tires	2 ply	---	2 ply	2 ply	4 ply	4 ply	4 ply	2 ply
Size	13x4-6	13x4-6	15x6.00-6	15x6.00-6	16x6.50-8	16x6.50-8	16x6.50-8	20x10.00-8
Tread design	Turf	Knobby	Turf	Turf	Turf	Turf	Turf	Turf
Recommended inflation pressure	30 psi (207 kPa)	30 psi (207 kPa)	14 psi (97 kPa)	14 psi (97 kPa)	35 psi (241 kPa)	28 psi (193 kPa)	28 psi (193 kPa)	10 psi (70 kPa)
Wheel bearings	Iron/Oilite	None	Iron/Oilite	Iron/Oilite	Iron/Oilite	Iron/Oilite	Iron/Oilite	Ball bearings, double sealed
Grease fittings on wheels	Yes	None	Yes	Yes	Yes	Yes	Yes	None
Axle diameter	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	1 in. (2.54 cm)	1 in. (2.54 cm)
Ground clearance	5.62 in. (14.3 cm)	5.25 in. (13.3 cm)	6.5 in. (16.5 cm)	6.5 in. (16.5 cm)	14.25 in. (36.2 cm)	14.25 in. (36.2 cm)	7 in. (17.8 cm)	8.25 in. (21 cm)
Width, overall	34 in. (86.4 cm)	33.68 in. (85.5 cm)	38 in. (96.5 cm)	38 in. (96.5 cm)	39.5 in. (100.3 cm)	39.5 in. (100.3 cm)	38 in. (96.5 cm)	48 in. (122 cm)
Hitch pin	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip
Dump angles	55 degrees	55 degrees	56 degrees	31 degrees	46 degrees	46 degrees	35/40 degrees	35/40 degrees
Maximum tongue weight	100 lb (45.4 kg)	100 lb (45.4 kg)	70 lb (31.75 kg)	100 lb (45.4 kg)	50 lb (22 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)
Shipping weight with carton	68 lb (31 kg)	65 lb (29.5 kg)	79 lb (35.8 kg)	110 lb (49.9 kg)	---	105 lb (47.6 kg)	170 lb (77.1 kg)	240 lb (109 kg)
Net weight	65 lb (29 kg)	55 lb (25 kg)	72 lb (32.7 kg)	105 lb (47.6 kg)	103 lb (47 kg)	105 lb (47.6 kg)	150 lb (68 kg)	220 lb (99.8 kg)

*Total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg).

**HDPE is compression molded for optimum thickness in all areas and maximum durability.

Tractor compatibility and requirements

Utility Carts

Chart below shows vehicle compatibility.

An X indicates cart can be used with the pulling unit.

NOTE: For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The chart shows which utility carts are compatible with the vehicle.

 

	7P	8Y	10P	13	16YS	17P	18	21
EZtrak Z225, Z235, Z245, Z255, Z425, Z435, Z445, Z465, Z625, Z645, Z655, Z665 ZTrak Z335E, Z355E, Z335M, Z345M, Z345R, Z355R, Z375R, Z525E, Z535M, Z540M, Z535R, Z540R, Z720E, Z735E, Z730M, Z735M, Z740R	X		X
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D125, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180	X	X	X	X	X	X	X
S240	X	X	X	X	X	X	X
LT150, LT160, LT180, LT190, LTR180	X	X	X		X	X
LX280, LX280AWS, LX289	X	X	X		X	X
X300, X300R, X304, X310, X320, X324, X340, X360, X330, X350, X350R, X354, X370, X380, X384, X390, X394	X	X	X	X	X	X	X
SST15, SST16, SST18	X	X	X
G110	X	X	X	X	X	X
GT235, GT245	X	X	X	X	X	X
GX255, GX335, GX345, GX355	X	X	X	X	X	X
X500, X520, X530, X534, X540 X570, X580, X584, X590	X	X	X	X	X	X	X
X465, X475, X485, X495, X575, X585, X595	X	X	X	X	X	X	X	X
X700, X720, X724, X728, X729, X740, X744, X748, X749 X710, X730, X734, X738, X739, X750, X754, X758	X	X	X	X	X	X	X	X

For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). See the appropriate vehicle pages for the weight of the vehicle and the mower deck. Additional weight can be added to the vehicle by the following methods:

  

Tractor	Additional weight
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180	Two 30-lb (14-kg) wheel weights, front Two 42-lb (19-kg) suitcase weights, rear
S240	Two 34-lb (15-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, rear
LT150, LT160, LT180, LT190, LTR180	Two 34-lb (15-kg) wheel weights, front Two 31-lb (14.1-kg) plastic shell wheel weights, rear (not for LT190)
LX280, LX280AWS, LX289 X300, X300R, X304, X310, X320, X324, X340, X360 X330, X350, X350R, X354, X370, X380, X384, X390, X394	Two 34-lb (15-kg) wheel weights, front Four 42-lb (19-kg) suitcase weights, rear
SST15, SST16, SST18	One 88-lb (40-kg) weight kit, front Three 40-lb (18-kg) weights, rear
G100	Two 50-lb (23-kg) wheel weights, rear Two 42-lb (19-kg) suitcase weights, rear
G110	Two 50-lb (23-kg) plastic shell rear wheel weights
GT235, GT245	Two 30-lb (14-kg) wheel weights, front Four 42-lb (19-kg) suitcase weights, front Four 42-lb (19-kg) suitcase weights, rear Four 50-lb (23-kg) wheel weights, rear Two 50-lb (23-kg) plastic shell wheel weights, rear
GX255, GX335, GX345, GX355 X500, X520, X530, X534, X540 X570, X580, X584, X590	Two 30-lb (14-kg) wheel weights, front Four 42-lb (19-kg) suitcase weights, front Four 42-lb (19-kg) suitcase weights, rear Four 50-lb (23-kg) wheel weights, rear Two 50-lb (23-kg) wheel plastic shell weights, rear
X465, X475, X485, X495, X575, X585, X595 X700, X720, X724, X728, X729, X740, X744, X748, X749 X710, X730, X734, X738, X739, X750, X754, X758	Four 42-lb (19-kg) suitcase weights, front Two 70-lb (32-kg) wheel cast-iron starter weights, rear Four 50-lb (23-kg) cast-iron wheel weights, rear Two 50-lb (23-kg) plastic shell wheel weights, rear Six 42-lb (19-kg) suitcase weights, rear

 

Ordering information

Please contact a local John Deere dealer for availability and pricing information.

13 Utility Cart
Order number: LPHDC13JD

Oilite is a trademark of Beemer Precision, Incorporated.

The 17-cu-ft (0.48-m³), 800-lb (363-kg) capacity or 350 lb (158 kg) when using swivel feature to dump 16YS Swivel Cart is unique in the lineup of John Deere carts in that it can be swiveled 120 degrees to either side for easier unloading. The operator can simply pull up next to where they want to dump the material and swivel the cart, eliminating the need to back up the cart.

 

Key features include:

• Haul a variety of materials including lawn debris, sand, dirt, mulch, and plants
• 800-lb (363-kg) capacity makes it durable enough for the heavy jobs
  • 350 lb (158 kg) when using swivel feature to dump
• Convenient foot pedal release for easy dumping
• Molded stake pockets for enlarging the bed size

NOTE: Do not exceed 350 lb (158 kg) weight capacity when using swivel feature to dump.

 

Every owner of a John Deere riding lawn and garden product is a potential customer for a high-quality, affordable utility cart. Utility carts can be used to haul a variety of materials including firewood, lawn debris, sand, dirt, mulch, garden tools, plants, and bushes. Utility carts are designed, painted, and decaled to be compatible with other John Deere equipment.

 

NOTE: For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. See the appropriate vehicle pages for the weight of the vehicle and the mower deck.

Model comparison chart

Comparison with similar models

Model	Order through	Box capacity (heaped)	Material thickness	Maximum weight	Vehicle compatibility
7P	Order Zone	7 cu ft (0.20 m3)	High-density polyethylene (HDPE)**	450 lb* (204 kg)	EZtrak™, ZTrak™, 100 Series, S240, X300 Series, X500 Series, X700 Series
8Y	Order Zone	8 cu ft (0.22 m3)	HDPE**	300 lb* (136 kg) (tow)	100 Series, S240, X300 Series, X500 Series, X700 Series
10P	Order Zone	10 cu ft (0.28 m3)	Polypropylene	650 lb* (295 kg)	EZtrak, ZTrak, 100 Series, S240, X300 Series, X500 Series, X700 Series
13	Order Zone	13 cu ft (0.37 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,000 lb* (454 kg)	100 Series, S240, X300 Series, X500 Series, X700 Series
16YS	Order Zone	17 cu ft (0.48 m3)	Polypropylene	800 lb (363 kg), 350 lb (158 kg) when using swivel feature to dump	100 Series, S240, X300 Series, X500 Series, X700 Series
17P	Order Zone	17 cu ft (0.48 m3)	Polypropylene	1,000 lb* (454 kg)	100 Series, S240, X300 Series, X500 Series, X700 Series
18	Order Zone	18 cu ft (0.51 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,000 lb* (454 kg)	100 Series, S240, X300 Series, X500 Series, X700 Series
21	Order Zone	21 cu ft (0.59 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,000 lb* (454 kg)	X700 Series

*The total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The maximum weight for the 21 Utility Cart is rated at 20 mph (32.2 km/h).

**HDPE is compression molded for optimum thickness in all areas and maximum durability.

Specifications

 

	7P	8Y	10P	13	16YS	17P	18	21
Box capacity
Heaped	7 cu ft (0.20 m3)	8 cu ft (0.22 m3)	10 cu ft (0.28 m3)	13 cu ft (0.37 m3)	17 cu ft (0.48 m3)	17 cu ft (0.48 m3)	18 cu ft (0.51 m3)	21 cu ft (0.59 m3)
Struck	5.6 cu ft (0.16 m3)	6.6 cu ft (0.19 m3)	8.3 cu ft (0.24 m3)	10 cu ft (0.28 m3)	15 cu ft (0.42 m3)	14 cu ft (0.40 m3)	15 cu ft (0.42 m3)	15 cu ft (0.42 m3)
Maximum weight	450 lb* (204 kg)	300 lb* (136 kg)	650 lb* (295 kg)	1,000 lb* (454 kg)	800 lb* (363 kg), 350 lb (158 kg) when using swivel feature to dump	1,000 lb* (454 kg)	1,000 lb* (454 kg)	1,000 lb* (454 kg)
Box dimensions
Width	33 in. (84 cm)	33.68 in. (85.5 cm)	30.3 in. (77 cm)	30.25 in. (76.8 cm)	39.5 in. (100.3 cm)	39.5 in. (100.3 cm)	38 in. (96.5 cm)	48 in. (122 cm)
Length	45 in. (114 cm)	45 in. (114 cm)	44.5 in. (113 cm)	48 in. (122 cm)	58.5 in. (148.6 cm)	58.5 in. (148.6 cm)	48 in. (122 cm)	48 in. (122 cm)
Depth	10.5 in. (27 cm)	10.75 in. (27.3cm)	12 in. (30.5 cm)	12 in. (30.5 cm)	15.5 in. (39.4 cm)	15.5 in. (39.4 cm)	18 in. (45.7 cm)	11 in. (27.9 cm)
Box construction	Molded	Molded	Molded	Welded	Molded	Molded	Welded	Bolted
Material	High-density polyethylene (HDPE)**	HDPE** w/UV inhibitor	Polypropylene	16-gauge, 0.06-in. (1.5-mm) steel	Polypropylene	Polypropylene	16-gauge, 0.06-in. (1.5-mm) steel	16-gauge, 0.06-in. (1.5-mm) steel
Tailgate	None, sloped	None, sloped	None, sloped	Hinged	None, sloped	None, sloped	Hinged	Lift-out/swing-out
Pneumatic tires	2 ply	---	2 ply	2 ply	4 ply	4 ply	4 ply	2 ply
Size	13x4-6	13x4-6	15x6.00-6	15x6.00-6	16x6.50-8	16x6.50-8	16x6.50-8	20x10.00-8
Tread design	Turf	Knobby	Turf	Turf	Turf	Turf	Turf	Turf
Recommended inflation pressure	30 psi (207 kPa)	30 psi (207 kPa)	14 psi (97 kPa)	14 psi (97 kPa)	35 psi (241 kPa)	28 psi (193 kPa)	28 psi (193 kPa)	10 psi (70 kPa)
Wheel bearings	Iron/Oilite	None	Iron/Oilite	Iron/Oilite	Iron/Oilite	Iron/Oilite	Iron/Oilite	Ball bearings, double sealed
Grease fittings on wheels	Yes	None	Yes	Yes	Yes	Yes	Yes	None
Axle diameter	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	1 in. (2.54 cm)	1 in. (2.54 cm)
Ground clearance	5.62 in. (14.3 cm)	5.25 in. (13.3 cm)	6.5 in. (16.5 cm)	6.5 in. (16.5 cm)	14.25 in. (36.2 cm)	14.25 in. (36.2 cm)	7 in. (17.8 cm)	8.25 in. (21 cm)
Width, overall	34 in. (86.4 cm)	33.68 in. (85.5 cm)	38 in. (96.5 cm)	38 in. (96.5 cm)	39.5 in. (100.3 cm)	39.5 in. (100.3 cm)	38 in. (96.5 cm)	48 in. (122 cm)
Hitch pin	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip
Dump angles	55 degrees	55 degrees	56 degrees	31 degrees	46 degrees	46 degrees	35/40 degrees	35/40 degrees
Maximum tongue weight	100 lb (45.4 kg)	100 lb (45.4 kg)	70 lb (31.75 kg)	100 lb (45.4 kg)	50 lb (22 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)
Shipping weight with carton	68 lb (31 kg)	65 lb (29.5 kg)	79 lb (35.8 kg)	110 lb (49.9 kg)	---	105 lb (47.6 kg)	170 lb (77.1 kg)	240 lb (109 kg)
Net weight	65 lb (29 kg)	55 lb (25 kg)	72 lb (32.7 kg)	105 lb (47.6 kg)	103 lb (47 kg)	105 lb (47.6 kg)	150 lb (68 kg)	220 lb (99.8 kg)

*Total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg).

**HDPE is compression molded for optimum thickness in all areas and maximum durability.

Tractor compatibility and requirements

Utility Carts

Chart below shows vehicle compatibility.

An X indicates cart can be used with the pulling unit.

NOTE: For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The chart shows which utility carts are compatible with the vehicle.

 

	7P	8Y	10P	13	16YS	17P	18	21
EZtrak Z225, Z235, Z245, Z255, Z425, Z435, Z445, Z465, Z625, Z645, Z655, Z665 ZTrak Z335E, Z355E, Z335M, Z345M, Z345R, Z355R, Z375R, Z525E, Z535M, Z540M, Z535R, Z540R, Z720E, Z735E, Z730M, Z735M, Z740R	X		X
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D125, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180	X	X	X	X	X	X	X
S240	X	X	X	X	X	X	X
LT150, LT160, LT180, LT190, LTR180	X	X	X		X	X
LX280, LX280AWS, LX289	X	X	X		X	X
X300, X300R, X304, X310, X320, X324, X340, X360, X330, X350, X350R, X354, X370, X380, X384, X390, X394	X	X	X	X	X	X	X
SST15, SST16, SST18	X	X	X
G110	X	X	X	X	X	X
GT235, GT245	X	X	X	X	X	X
GX255, GX335, GX345, GX355	X	X	X	X	X	X
X500, X520, X530, X534, X540 X570, X580, X584, X590	X	X	X	X	X	X	X
X465, X475, X485, X495, X575, X585, X595	X	X	X	X	X	X	X	X
X700, X720, X724, X728, X729, X740, X744, X748, X749 X710, X730, X734, X738, X739, X750, X754, X758	X	X	X	X	X	X	X	X

For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). See the appropriate vehicle pages for the weight of the vehicle and the mower deck. Additional weight can be added to the vehicle by the following methods:

  

Tractor	Additional weight
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180	Two 30-lb (14-kg) wheel weights, front Two 42-lb (19-kg) suitcase weights, rear
S240	Two 34-lb (15-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, rear
LT150, LT160, LT180, LT190, LTR180	Two 34-lb (15-kg) wheel weights, front Two 31-lb (14.1-kg) plastic shell wheel weights, rear (not for LT190)
LX280, LX280AWS, LX289 X300, X300R, X304, X310, X320, X324, X340, X360 X330, X350, X350R, X354, X370, X380, X384, X390, X394	Two 34-lb (15-kg) wheel weights, front Four 42-lb (19-kg) suitcase weights, rear
SST15, SST16, SST18	One 88-lb (40-kg) weight kit, front Three 40-lb (18-kg) weights, rear
G100	Two 50-lb (23-kg) wheel weights, rear Two 42-lb (19-kg) suitcase weights, rear
G110	Two 50-lb (23-kg) plastic shell rear wheel weights
GT235, GT245	Two 30-lb (14-kg) wheel weights, front Four 42-lb (19-kg) suitcase weights, front Four 42-lb (19-kg) suitcase weights, rear Four 50-lb (23-kg) wheel weights, rear Two 50-lb (23-kg) plastic shell wheel weights, rear
GX255, GX335, GX345, GX355 X500, X520, X530, X534, X540 X570, X580, X584, X590	Two 30-lb (14-kg) wheel weights, front Four 42-lb (19-kg) suitcase weights, front Four 42-lb (19-kg) suitcase weights, rear Four 50-lb (23-kg) wheel weights, rear Two 50-lb (23-kg) wheel plastic shell weights, rear
X465, X475, X485, X495, X575, X585, X595 X700, X720, X724, X728, X729, X740, X744, X748, X749 X710, X730, X734, X738, X739, X750, X754, X758	Four 42-lb (19-kg) suitcase weights, front Two 70-lb (32-kg) wheel cast-iron starter weights, rear Four 50-lb (23-kg) cast-iron wheel weights, rear Two 50-lb (23-kg) plastic shell wheel weights, rear Six 42-lb (19-kg) suitcase weights, rear

Ordering information

Please contact a local John Deere dealer for availability and pricing information.

 

16YS Swivel Cart

Order number: LP68186

Oilite is a trademark of Beemer Precision Incorporated.

Every owner of a John Deere riding lawn and garden product is a potential user of a high-quality, affordable utility cart.

Utility carts can be used to haul a variety of materials:

• Firewood
• Lawn debris
• Sand
• Dirt
• Mulch
• Garden tools
• Plants and bushes

Utility carts are designed, painted, and decaled to be compatible with other John Deere equipment.

 

Key features of the 17P Utility Cart:

• 1,000-lb (454-kg), 17-cu ft (0.48-m³) load capacity.
• Cart has premium molded polypropylene box construction.
• Polypropylene body will not rust or dent, staying new-looking longer.
• 0.75- x 2-in. (19- x 51-mm) stake pockets are molded in to make addition of side extensions easy.
• Two vertical 0.75-in. (19-mm) molded channels on each side allow for easy use of dividers to separate the box into two or three compartments.
• Ribs in box bottom add strength and prevent a shovel from hitting bolts when emptying the cart.
• Sloped tailgate design makes emptying the box easier; no tailgate to loosen or remove.
• Styling is compatible with other John Deere equipment.
• 16x6.5 pneumatic tires with turf tread give good flotation, shock absorption, and minimal rolling resistance.
• Wheels are mounted on a solid one-piece axle.
• Wheels turn on iron/Oilite® bushings with grease fitting for long life.
• Spring-loaded dump latch is easy to use.

A convenient foot pedal dump release kit, LP48017, which now comes standard on all 10P and 17P carts is available to retrofit existing poly carts. This kit allows the operator to use both hands to lift the cart bed for more natural and efficient unloading.

Model comparison chart

Comparison with similar models

Model	Order through	Box capacity (heaped)	Material thickness	Maximum weight	Vehicle compatibility
7P	Order Zone	7 cu ft (0.20 m3)	High-density polyethylene (HDPE)**	450 lb* (204 kg)	EZtrak™, ZTrak™, 100 Series, S240, X300 Series, X500 Series, X700 Series
8Y	Order Zone	8 cu ft (0.22 m3)	HDPE**	300 lb* (136 kg) (tow)	100 Series, S240, X300 Series, X500 Series, X700 Series
10P	Order Zone	10 cu ft (0.28 m3)	Polypropylene	650 lb* (295 kg)	EZtrak, ZTrak, 100 Series, S240, X300 Series, X500 Series, X700 Series
13	Order Zone	13 cu ft (0.37 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,000 lb* (454 kg)	100 Series, S240, X300 Series, X500 Series, X700 Series
16YS	Order Zone	17 cu ft (0.48 m3)	Polypropylene	800 lb (363 kg), 350 lb (158 kg) when using swivel feature to dump	100 Series, S240, X300 Series, X500 Series, X700 Series
17P	Order Zone	17 cu ft (0.48 m3)	Polypropylene	1,000 lb* (454 kg)	100 Series, S240, X300 Series, X500 Series, X700 Series
18	Order Zone	18 cu ft (0.51 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,000 lb* (454 kg)	100 Series, S240, X300 Series, X500 Series, X700 Series
21	Order Zone	21 cu ft (0.59 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,000 lb* (454 kg)	X700 Series

*The total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The maximum weight for the 21 Utility Cart is rated at 20 mph (32.2 km/h).

**HDPE is compression molded for optimum thickness in all areas and maximum durability.

Specifications

 

	7P	8Y	10P	13	16YS	17P	18	21
Box capacity
Heaped	7 cu ft (0.20 m3)	8 cu ft (0.22 m3)	10 cu ft (0.28 m3)	13 cu ft (0.37 m3)	17 cu ft (0.48 m3)	17 cu ft (0.48 m3)	18 cu ft (0.51 m3)	21 cu ft (0.59 m3)
Struck	5.6 cu ft (0.16 m3)	6.6 cu ft (0.19 m3)	8.3 cu ft (0.24 m3)	10 cu ft (0.28 m3)	15 cu ft (0.42 m3)	14 cu ft (0.40 m3)	15 cu ft (0.42 m3)	15 cu ft (0.42 m3)
Maximum weight	450 lb* (204 kg)	300 lb* (136 kg)	650 lb* (295 kg)	1,000 lb* (454 kg)	800 lb* (363 kg), 350 lb (158 kg) when using swivel feature to dump	1,000 lb* (454 kg)	1,000 lb* (454 kg)	1,000 lb* (454 kg)
Box dimensions
Width	33 in. (84 cm)	33.68 in. (85.5 cm)	30.3 in. (77 cm)	30.25 in. (76.8 cm)	39.5 in. (100.3 cm)	39.5 in. (100.3 cm)	38 in. (96.5 cm)	48 in. (122 cm)
Length	45 in. (114 cm)	45 in. (114 cm)	44.5 in. (113 cm)	48 in. (122 cm)	58.5 in. (148.6 cm)	58.5 in. (148.6 cm)	48 in. (122 cm)	48 in. (122 cm)
Depth	10.5 in. (27 cm)	10.75 in. (27.3cm)	12 in. (30.5 cm)	12 in. (30.5 cm)	15.5 in. (39.4 cm)	15.5 in. (39.4 cm)	18 in. (45.7 cm)	11 in. (27.9 cm)
Box construction	Molded	Molded	Molded	Welded	Molded	Molded	Welded	Bolted
Material	High-density polyethylene (HDPE)**	HDPE** w/UV inhibitor	Polypropylene	16-gauge, 0.06-in. (1.5-mm) steel	Polypropylene	Polypropylene	16-gauge, 0.06-in. (1.5-mm) steel	16-gauge, 0.06-in. (1.5-mm) steel
Tailgate	None, sloped	None, sloped	None, sloped	Hinged	None, sloped	None, sloped	Hinged	Lift-out/swing-out
Pneumatic tires	2 ply	---	2 ply	2 ply	4 ply	4 ply	4 ply	2 ply
Size	13x4-6	13x4-6	15x6.00-6	15x6.00-6	16x6.50-8	16x6.50-8	16x6.50-8	20x10.00-8
Tread design	Turf	Knobby	Turf	Turf	Turf	Turf	Turf	Turf
Recommended inflation pressure	30 psi (207 kPa)	30 psi (207 kPa)	14 psi (97 kPa)	14 psi (97 kPa)	35 psi (241 kPa)	28 psi (193 kPa)	28 psi (193 kPa)	10 psi (70 kPa)
Wheel bearings	Iron/Oilite	None	Iron/Oilite	Iron/Oilite	Iron/Oilite	Iron/Oilite	Iron/Oilite	Ball bearings, double sealed
Grease fittings on wheels	Yes	None	Yes	Yes	Yes	Yes	Yes	None
Axle diameter	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	1 in. (2.54 cm)	1 in. (2.54 cm)
Ground clearance	5.62 in. (14.3 cm)	5.25 in. (13.3 cm)	6.5 in. (16.5 cm)	6.5 in. (16.5 cm)	14.25 in. (36.2 cm)	14.25 in. (36.2 cm)	7 in. (17.8 cm)	8.25 in. (21 cm)
Width, overall	34 in. (86.4 cm)	33.68 in. (85.5 cm)	38 in. (96.5 cm)	38 in. (96.5 cm)	39.5 in. (100.3 cm)	39.5 in. (100.3 cm)	38 in. (96.5 cm)	48 in. (122 cm)
Hitch pin	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip
Dump angles	55 degrees	55 degrees	56 degrees	31 degrees	46 degrees	46 degrees	35/40 degrees	35/40 degrees
Maximum tongue weight	100 lb (45.4 kg)	100 lb (45.4 kg)	70 lb (31.75 kg)	100 lb (45.4 kg)	50 lb (22 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)
Shipping weight with carton	68 lb (31 kg)	65 lb (29.5 kg)	79 lb (35.8 kg)	110 lb (49.9 kg)	---	105 lb (47.6 kg)	170 lb (77.1 kg)	240 lb (109 kg)
Net weight	65 lb (29 kg)	55 lb (25 kg)	72 lb (32.7 kg)	105 lb (47.6 kg)	103 lb (47 kg)	105 lb (47.6 kg)	150 lb (68 kg)	220 lb (99.8 kg)

*Total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg).

**HDPE is compression molded for optimum thickness in all areas and maximum durability.

Tractor compatibility and requirements

Utility Carts

Chart below shows vehicle compatibility.

An X indicates cart can be used with the pulling unit.

NOTE: For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The chart shows which utility carts are compatible with the vehicle.

 

	7P	8Y	10P	13	16YS	17P	18	21
EZtrak Z225, Z235, Z245, Z255, Z425, Z435, Z445, Z465, Z625, Z645, Z655, Z665 ZTrak Z335E, Z355E, Z335M, Z345M, Z345R, Z355R, Z375R, Z525E, Z535M, Z540M, Z535R, Z540R, Z720E, Z735E, Z730M, Z735M, Z740R	X		X
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D125, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180	X	X	X	X	X	X	X
S240	X	X	X	X	X	X	X
LT150, LT160, LT180, LT190, LTR180	X	X	X		X	X
LX280, LX280AWS, LX289	X	X	X		X	X
X300, X300R, X304, X310, X320, X324, X340, X360, X330, X350, X350R, X354, X370, X380, X384, X390, X394	X	X	X	X	X	X	X
SST15, SST16, SST18	X	X	X
G110	X	X	X	X	X	X
GT235, GT245	X	X	X	X	X	X
GX255, GX335, GX345, GX355	X	X	X	X	X	X
X500, X520, X530, X534, X540 X570, X580, X584, X590	X	X	X	X	X	X	X
X465, X475, X485, X495, X575, X585, X595	X	X	X	X	X	X	X	X
X700, X720, X724, X728, X729, X740, X744, X748, X749 X710, X730, X734, X738, X739, X750, X754, X758	X	X	X	X	X	X	X	X

For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). See the appropriate vehicle pages for the weight of the vehicle and the mower deck. Additional weight can be added to the vehicle by the following methods:

  

Tractor	Additional weight
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180	Two 30-lb (14-kg) wheel weights, front Two 42-lb (19-kg) suitcase weights, rear
S240	Two 34-lb (15-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, rear
LT150, LT160, LT180, LT190, LTR180	Two 34-lb (15-kg) wheel weights, front Two 31-lb (14.1-kg) plastic shell wheel weights, rear (not for LT190)
LX280, LX280AWS, LX289 X300, X300R, X304, X310, X320, X324, X340, X360 X330, X350, X350R, X354, X370, X380, X384, X390, X394	Two 34-lb (15-kg) wheel weights, front Four 42-lb (19-kg) suitcase weights, rear
SST15, SST16, SST18	One 88-lb (40-kg) weight kit, front Three 40-lb (18-kg) weights, rear
G100	Two 50-lb (23-kg) wheel weights, rear Two 42-lb (19-kg) suitcase weights, rear
G110	Two 50-lb (23-kg) plastic shell rear wheel weights
GT235, GT245	Two 30-lb (14-kg) wheel weights, front Four 42-lb (19-kg) suitcase weights, front Four 42-lb (19-kg) suitcase weights, rear Four 50-lb (23-kg) wheel weights, rear Two 50-lb (23-kg) plastic shell wheel weights, rear
GX255, GX335, GX345, GX355 X500, X520, X530, X534, X540 X570, X580, X584, X590	Two 30-lb (14-kg) wheel weights, front Four 42-lb (19-kg) suitcase weights, front Four 42-lb (19-kg) suitcase weights, rear Four 50-lb (23-kg) wheel weights, rear Two 50-lb (23-kg) wheel plastic shell weights, rear
X465, X475, X485, X495, X575, X585, X595 X700, X720, X724, X728, X729, X740, X744, X748, X749 X710, X730, X734, X738, X739, X750, X754, X758	Four 42-lb (19-kg) suitcase weights, front Two 70-lb (32-kg) wheel cast-iron starter weights, rear Four 50-lb (23-kg) cast-iron wheel weights, rear Two 50-lb (23-kg) plastic shell wheel weights, rear Six 42-lb (19-kg) suitcase weights, rear

Ordering information

Please contact a local John Deere dealer for availability and pricing information.

 

17P Utility Cart
Order number: LPPCT17JD

Oilite is a trademark of Beemer Precision Incorporated.

The hopper design provides efficient bagging performance, clean operation, and easy-to-empty bags:

• Two durable bags with a generous, 6.5-bu (229-L) capacity lift out for emptying and are easy to reinstall.
• Efficient lower chute provides smooth flow of material to reduce chance of plugging.
• An air-exhaust duct directs air from the hopper back and toward the ground for clean operation.
• A convenient bungee-cord fastener makes opening and closing the hopper easy.
• It is easy to install and remove the hopper, and no tools are required after the initial installation.
• Pins and spring clips hold the hopper and chute in place; there is nothing left to interfere with other attachments when removed.
• Loose-knit bags allow more air to flow through to provide complete bag filling in wet and heavy grass conditions.

Specifications

 

Capacity	6.5 bu (229 L)
Material
Hopper top	Cross-linked high-density polyethylene (HDPE)
Chute	Polyethylene
Bags	Polypropylene
Filling	Directly into bags for emptying on the ground, into a trailer, or into plastic liners

Tractor compatibility and requirements

The 6.5-bu (229-L) rear bagger is for use with:

• 100 Series and S240 Tractors equipped with a 42-in. (107-cm) Mower

 

Requirements and/or recommendations:

• Front ballast is recommended when bagging, especially on hills or inclines.
• Use of rear tow-behind attachments that could come in contact with the hopper assembly is not recommended when the hopper assembly is installed.
• Special mower blades are not required.
• High-lift mower blades for use in difficult bagging conditions are included with BG20776 6.5-bu (229-L) hopper and chute for 100 Series and S240 Tractors, 42 in. (107 cm).

Dump from the seat capability for 100 Series Tractors with a 6.5-bu material collection system (MCS)

The MCS 6 attachment is designed to provide dump from the seat grass collection/expulsion for John Deere 100 Series and S240 Tractors equipped with the 2-bag material collection system (MCS). The MCS attachment eliminates the need to get off of the tractor and empty the bags. As a result, it will increase both efficiency and cleanliness in the mowing process.

The aluminum body is lightweight and easy to handle. Conveniently located hand lever and smooth release and latching system are easily accessed from the tractor seat. Because it is engineered specifically for the John Deere Material Collection System, installation is a breeze with simple hand tools.

Features:

• Lightweight aluminum construction
• Designed for full material expulsion
• Easy access self-latching spring tripped handle
• Ships almost fully assembled (5 minute handle assembly)
• Installs in seconds (after initial assembly)

Benefits:

• Easy - Convenient Access to dump handle directly from seat 
• Clean - No material handling, no mess 
• Efficient - Unload and go without leaving the seat 

NOTE: Fits John Deere 100 Series and S240 Tractor 2-bag material collection systems. Not compatible with EZtrak™ Zero-Turn Mowers.

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

 

MCS 6 attachment
Order number: LP47167

Fits John Deere lawn and garden tow behind attachments.

• Strong magnetic grip
• Rust resistant
• Easy to install, secure fit

Ordering information

Customers, please contact your local John Deere dealer for availability and pricing information.

Magnetic hitch pin

Order number: LP63768

The front blade is excellent for pushing light snow or other loose material.

The blade is constructed for good performance and long life:

• Blade surface is curved to roll rather than push material, which requires less power and increased blade capacity.
• Bolt-on, replaceable cutting edge takes most of the wear to greatly extend the useful life of the blade.

For operator convenience, the blade comes with standard equipment for controlling it from the tractor seat:

• Blade can be angled left, right, or used in the straight-ahead position.

Full working range

The 46-in. (117-cm) blade can be operated up to 6.5 in. (16.5 cm) above ground level.

Floating action is designed into the lift linkage, so the blade is free to follow the contour of the ground.

The lift-linkage design makes raising the blade easy.

Controlled from tractor seat

For operator convenience, the blade comes with angling and lift components as standard equipment so it can be controlled from the tractor seat.

Front blade lift and angling components are included as standard equipment:

• Blade can be angled left, right, or used in the straight-ahead position.
• For 100 Series Tractors, L100 Series Lawn Tractors, G110 Garden Tractors, and S240 Tractor, lift components are provided with the blade so it can be raised and lowered from the tractor seat.

Specifications

Overall width	46 in. (117 cm)
Overall height	14 in. (36 cm)
Clearing width	46 in. (117 cm)
Angling positions	Three
Lift height	6.5 in. (17 cm)
Net weight	73 lb (33.1 kg)

Tractor compatibility and requirements

The 46-in. (117-cm) Front Blade is compatible with:

• 102, 115, 125, 135, 145, 155C, and 190C Tractors
• L100, L108, L110, L111, L118, L120, and L130 Lawn Tractors, and G110 Garden Tractor
• LA100, LA110, LA120, LA130, LA140, and LA150 Tractors
• LA105, LA115, LA125, LA135 Limited Edition, LA135 Special Edition, LA145, LA155, LA165, and LA175 Tractors
• D100, D105, D110, D120, D125, D130, D140, D150, D155, D160, D170 Tractors
• S240 Tractor

For model years 2016 and newer, the 46-in. (117-cm) Front Blade (BG20943) has a change to the mounting frame to make it compatible with model year 2016 and newer D100 Series and S240 Tractors:

• The model years 2016 and newer Front Blades are also backward compatible with model year 2015 and older D100 Series Tractors and the S240 Tractor.
• The model year 2015 46-in. (117-cm) Front Blade (BG20020) is not compatible with model year 2016 and newer tractors (SN 700,001-).
  • A model year 2016 and newer tractor steering change from a dual drag link system to a single drag link and tie rod design causes interference with older front blades.

Attachment			D100 Series and S240 Tractors
Model year	Description	Order code/attachment number	2015 and prior	2016 and newer
2015 and prior	46-in. (117-cm) Front Blade	BG20020	X
2016 and newer	46-in. (117-cm) Front Blade	BG20943	X	X

Requirements and/or recommendations:

• Rear weights and tire chains are required for additional traction.

AUC13705 home maintenance kit

Home maintenance kits are a handy and convenient way for dealers to supply an owner with the maintenance ­interval parts as specified in their operator's manual.

 

The AUC13705 home maintenance kit includes the following:

 

Quantity	Description
1	Easy Change 30-second oil change system
1	Fuel filter
1	Air filter cartridge
2	Spark plugs

This fully automatic 1.5-amp battery charger and maintainer safely charges lawn and garden, RV, deep-cycle, and most batteries that require long storage periods. It is particularly useful during winter months when the vehicle is not being used regularly, to ensure the battery stays charged:

• Automatically determines if the battery is 6- or 12-V and adjusts accordingly
• Helps maintain battery in good condition and ensures it is fully charged
• Powers on to charge battery and powers off when fully charged
• 'Onboard' feature allows mounting next to the battery on collector, street rods, and other occasional-use vehicles
• 1.5-amp trickle charges small batteries in 2 to 12 hours
• Maintains large battery charges
• Hookup protection guards battery and charger from damage 

 

Includes a choice of battery connection methods:

• Standard color-coded clips to connect to any battery
• Cable with quick-disconnect plug and end loops that can be bolted to battery terminals and easily unplugged from charger when not in use

Transporting mulch, plants, or debris is easier with the CargO Mount™ single bucket holder. Just slip the holder bracket into the tractor's rear CargO Mounts. For use with any standard 5-gal. (19-L) or 6-gal. (23-L) bucket, the bucket holder is designed to carry up to 70 lb (32 kg) of material.

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

Bucket holder (single)
Order number: LPJD100

Transporting mulch, plants, or debris is easy with the CargO Mount™ single bucket holder. Just slip the holder bracket into the tractor's rear CargO Mounts. Its all-steel construction enables it to carry up to 40 lb (18.1 kg) of material.

Ordering information

This version of the product that includes a bucket has been discontinued.

Bucket holder (single) with bucket
Order number: LPJD100W

This black 5-gal. (19-L) bucket perfectly complements the CargO Mount™ single and double bucket holders. It is made of sturdy black plastic.

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

Bucket - 5 gal. (19-L)
Order number: LPJD400

John Deere Fuel-Protect gasoline stabilizer is a unique formula developed to ensure optimum performance and protection year-round: 

• Has corrosion preventers
• For lawn and garden equipment and other gasoline-powered vehicles
• Ensures quick starts in all two- and four-cycle engines
• Use in gasoline, gasoline-oil mixture, and ethanol blends
• Use to treat gas cans at each fill-up or use at every fill-up of vehicle
• Keeps fuel fresh for 12 months
• Contains a fuel injector and carburetor cleaner
• 1 oz (29.6 mL) treats 2 gal. (7.6 L)

Always use fuel stabilizer in gasoline.

Fuel sitting in gas tanks or gas containers for more than 30 days begins to degrade. Also, blended fuels and water in gasoline can form acids that corrode fuel-system components. Protect the investment - use John Deere fuel stabilizer with corrosion preventers and prevent hard starting, surging, lack of power, poor idle, flooding, and will not run or stay running conditions caused by poor-quality fuel. Ask a local John Deere dealer or visit JDParts.

Helpful tips:

• Add fuel stabilizer every time fuel is purchased.
• Deere gasoline-powered equipment is recommended to run on a minimum of 87 octane gasoline.
• John Deere Fuel-Protect for gasoline is safe to use in all types of gasoline, including gasoline/oil mixtures and blended fuels containing up to 10 percent ethanol.
• Use plastic fuel containers to store fuel; ask a local John Deere dealer.
• For best results, use a spill-proof gas can that automatically seals the gas can vent.
• Store fuel in a cool, dry, dark place in a sealed fuel can.
• Fill tank to the top every time the machine is put away.
  • Make sure tank is drained if stored for the winter or treated if left for prolonged periods of time.

Please refer to the operator’s manual for additional recommendations and warranty information.

Fuel related issues are not considered a warrantable condition as there is no defect in the materials or workmanship of the machine. 

For more information on fuel, visit John Deere Groundscare.

The John Deere MowerPlus hour meter connector wirelessly links a model year 2003 and later 100 Series or S240 Lawn Tractor to the MowerPlus app on a mobile device:

• No tools are needed for installation.
• Detailed set-up instructions are included.
• The connector sends information to the MowerPlus app via Bluetooth® wireless technology when the tractor key switch is on and the mobile device app is running within range.
• The wireless connector and app work together to offer helpful information.

Tractor features available for viewing on the MowerPlus app include:

• Tractor engine hours automatically synchronized to the app
• In-app maintenance reminders and log, based on engine hours
• Help to determine the best time to mow
• Expert pre-mow optimization tips
• Maintenance walk-through instructions

The operator is able to visit their device’s app store to see new app features as they are added.

MowerPlus hour meter connector (BUC10510) for 100 Series and S240 Lawn Tractors

The hour meter connector plugs into the back of a 100 Series or S240 Tractor key switch. The tractor’s wiring harness plugs into the other end.

Compatibility and requirements

BUC10510 MowerPlus hour meter connector is for model year 2003 and later 100 Series and S240 Tractors, including model series E100, D100, LA100, L100, and S240.

MowerPlus hour meter connector requires the MowerPlus app on a mobile device to use. The John Deere MowerPlus app can be found in the mobile device’s app store:

• iOS® version 10 or higher is compatible with the hour meter connector.
• Android™ versions are not compatible with the hour meter connector at this time.

NOTE: The John Deere MowerPlus app is only available in the English language, and it is not available in all countries. Find operating system version availability in the mobile device’s app store.

Bluetooth is a trademark of Bluetooth SIG, Inc. Android is a trademark of Google LLC. iOS is a trademark of Cisco Technology, Inc. used under license by Apple Inc.

 

StarLock™ blade design

StarLock™ blade design

Features and benefits

• Homeowners can now achieve results just like the professionals.
• Brush is easy to adjust for varying mower cutting height.
• Brush adjusts to varying ground conditions and allows the operator to freely maneuver the vehicle without damaging the turf.
• The brush striping kit is a very economical and functional attachment.

Ordering information

Customers, please contact your local John Deere dealer for availability and pricing information.

 

42X - 42-in. (107-cm) tractor grass groomer

Order number: LP1001

A complete mower deck can be ordered for replacement, if required.

This 42-­in. (107-­cm) Mower Deck comes with two medium­-lift blades for normal cutting and bagging conditions.

NOTE: When replacing a model year 2015 or older mower deck, also order GY22387 power take-off (PTO) cable.

A complete mower deck can be ordered for replacement, if required.

Incomplete decks are also available through the John Deere Parts system. These decks include the shell, discharge chute, and decals.

This 42-­in. (107-­cm) Mower Deck comes with two medium­-lift blades for normal cutting and bagging conditions.

NOTE: When replacing a model year 2015 or older mower deck, also order GY22387 power take-off (PTO) cable.

The front blowout baffle kit is for the 42-in. (107-cm) Convertible Mower and the 42-in. (107-cm) Edge™ Xtra Mower. It will reduce the amount of blowout when bagging leaves or other dry material.

Leveling gauge allows quick and accurate mower deck leveling and cutting height adjustment.

Can be used for:

• Lawn tractors
• Lawn and garden tractors
• Riding mowers
• Front mowers
• Commercial walk-behind mowers
• Zero-turn-radius mowers

The mulch cover is available as an option.

The mulching attachment for the 42-in. (106.7-cm) mower deck provides excellent performance. This is a high-performance mulching attachment that includes a mulch plug and special mulching blades.

Features include:

• The blades included are designed to work with the StarLock™ blade mounting system used on the 42-in. (106.7-cm) mower deck for 100 Series Tractors, the S240 Tractor, and X300, X304, and X310 Tractors, and also for the 42-in. (106.7-cm) mower deck without the StarLock system used on LT Series Tractors.
• The special mulching blades included can also be used for side discharging, although the overall cut quality may decline slightly.

NOTE: The mulch plug included in the BM21816 mulch kit can also be used on the 42-in. (106.7-cm) mowers with L100 Series Tractors, but the special mulching blades included will not fit the mower spindle; the standard mower blades are designed for mulching and can continue to be used with the mulch plug in place.

The front bumper is an optional attachment for lawn tractors.

Benefits include:

• Additional front-end protection
• A more aggressive look for the tractor

Features include:

• Wipe-clean reinforced bottom around mower deck
• Easy-on side handles makes snugging down cover a snap
• Dual reinforced air vents let air circulate and help prevent ballooning in wind
• Interior lining and integrated muffler heat shield
• Heavy-duty fabric will not shrink or stretch and is coated for maximum water resistance
• Easy-on split back for fast fitting and easy access after installation
• Handy storage pocket reverses into an attractive storage case
• Two-year warranty

Cover provides heavy-duty protection for 100 Series, LT, LX, and S240 Tractors.

Ordering information

Customers, please contact your local John Deere dealer for availability and pricing information.

Protective cover (medium deluxe)

Order number: LP93617

Features include:

• Dual vents let air circulate and help prevent ballooning in wind
• Elastic shock cord in bottom hem for a quick, custom-like fit
• Coated fabric for maximum water protection
• One-year warranty

Cover provides all-season protection for 100 Series, S240 and Select Series™ X300 Series Tractors.

Ordering information

Customers, please contact your local John Deere dealer for availability and pricing information.

 

Protective cover (standard)

Order number: LP93917

Deluxe thick-cushioned seat cover provides superior protection, all-day riding comfort, and lots of storage:

• Access to lumbar adjustment controls
• Large-capacity rear-zippered cargo pocket
• Two side mesh beverage pockets
• Elastic cord in bottom hem for a custom fit
• Medium size fits seats with backrests up to 15 in. (38.1 cm)

Ordering information

Contact your local John Deere dealer for availability and pricing information.

Seat cover, deluxe medium
Order number: LP92624

Seat cover protects new seats and renews old seats:

• Cushioned seat for extra comfort
• Four convenient pockets for keeping tools and gear within reach
• Elastic cord in bottom hem for a custom fit
• Medium size fits seats with backrests up to 15 in. (381 mm)

Ordering information

Contact your local John Deere dealer for availability and pricing information.

Seat cover, standard medium
Order number: LP92324

Available to comply with laws in the state of California, requiring its use under certain conditions.

The law basically requires that purchasers of certain products be given written notice that it is illegal to use such machines on forest-covered, brush-covered or grass-covered land (except on watered lawns) without a spark arrester.

For further information on this law, consult No. 442.5 of the California Public Resources Code. Also available in other states to comply with local ordinances or customer requests.

The 15-gal. (57-L) tractor-mounted sprayer is compatible with the S240 and D100 Series Tractors. Convenient mounting, easy maneuverability, and overall versatility make this a perfect choice for a John Deere lawn tractor. It provides an excellent way to apply spray material, including liquid fertilizer, weed killer, tree spray, and de-icer. It comes complete with a 32-in. (81-cm) boom that sprays a 60-in. (152-cm) spray swath. It is also equipped with a 19-ft (5.8-m) hose and a spray wand for spot spraying lawns, shrubs, etc. The fully adjustable brass spray wand tip achieves streams up to 30 ft (9.1 m). It has a custom mounting bracket that utilizes the existing frame holes for no-tools mounting after initial assembly. A recirculation kit is included.

Features include:

• Custom mounting hardware uses existing frame holes
• Mounts in seconds after initial assembly
• Compatible with S240 and D100 Series Tractors
• SHURflo® 100 psi, 2.1 gpm (8 L/min) on-demand diaphragm-type pump is designed for high-hour commercial applications. It can be run dry without damage.
• The brass-tipped spray wand is included as standard equipment. It is constructed of non-corrosive polypropylene material with Viton® components for multi-use applications.
• Check valves in boom tips prevent siphoning and dripping, which can cause lawn spotting
• Recirculation keeps material mixed and moving
• Control valve directs spray to either the boom or spray wand
• Convenient electrical hookup includes all necessary wiring
• Rugged translucent yellow tank with molded fill-level indicators (in gal. and L)

Ordering information

Please contact a local John Deere dealer for availability and pricing information.

15-gal. (57-L) Mounted Sprayer for D100 Series and S240 Tractors

Order number: LP53283

SHURflo is a trademark of SHURflo, LLC.

Viton is a trademark DuPont Performance Elastomers.

Sprayer comes complete with a boom that sprays 60 in. (152.4 cm) wide. It also has a 12-ft (3.7-m) hose with an adjustable handgun for spot spraying lawns, shrubs, etc.

Features include:

• This sprayer is an excellent choice for spraying small- to moderate-size lawns and shrubs.
• Handgun with adjustable spray pattern is helpful when spraying fruit trees and can be used to spray trees up to 30-ft (9.1-m) high.
• A 14-in. (35.6-cm) wand on the handgun is standard equipment to give added convenience when spraying trees.

NOTE: Sprayers are compatible with competitive tractors (if equipped with a 12-V battery and charging system).

This sprayer is especially suited for maintaining residential and small commercial properties:

• Sprayers provide an excellent way to apply liquid fertilizer.
• Herbicides and pesticides can be applied along with liquid fertilizer or separately.

Advantages of using liquid fertilizer over dry fertilizer:

• Fertilizer is more readily available to plants.
• The fertilizer need not be worked into the soil by watering or rain before it will work.
• Herbicides are more effective when applied with liquid fertilizer.

NOTE: Use these sprayers with liquid-base lawn care chemicals only. They are not recommended for wettable powders as no agitating system is provided to prevent particles from separating out.

Ordering information

Customers, please contact your local John Deere dealer for availability and pricing information.

15-gal. (57-L) Tow-Behind Sprayer

Order number: LP19478

Sprayer comes with a wider boom that sprays a 90 in. (228.6 cm) width. A 15-ft (4.6-m) hose and handgun are provided.

Features include:

• 100 psi Shurflo® diaphragm-type pump is designed for high hour commercial applications. It can be run dry without damage.
• Sprayer is designed to be a good choice for customers with larger lawns with trees to care for or for light commercial spraying.
• Handgun with adjustable spray pattern is helpful when spraying fruit trees and can be used to spray trees up to 30 ft (9.1 m) in height.
• The 14-in. (35.6-cm) wand on the handgun is included as standard equipment.

NOTE: Sprayers are compatible with competitive tractors (if equipped with a 12-V battery and charging system).

This sprayer is especially suited for maintaining residential and small commercial properties.

• Sprayers provide an excellent way to apply liquid fertilizer.
• Herbicides and pesticides can be applied along with liquid fertilizer or separately.

Advantages of using liquid fertilizer over dry fertilizer:

• Fertilizer is more readily available to plants.
• The fertilizer need not be worked into the soil by watering or rain before it will work.
• Herbicides are more effective when applied with liquid fertilizer.

NOTE: Use this sprayer with liquid-based lawn care chemicals only. It is not recommended for wettable powders as no agitating system is provided to prevent particles from separating out.

Ordering information

Customers, please contact your local John Deere dealer for availability and pricing information.

25-gal. (95-L) Tow-Behind Sprayer

Order number: LP19479

SHURflo is a trademark of SHURflo, LLC.

John Deere spin spreaders have features and a choice of sizes to satisfy many operators. They are a popular attachment for both homeowner and commercial operators who use them for even distribution of a variety of materials:

• Seed
• Fertilizer
• Insecticide
• Salt

All spreaders have rust-resistant stainless-steel or polyethylene hoppers as well as many stainless-steel components to ensure lasting appearance and long, trouble-free operation.

Features include:

• Positive on/off system (no cables)
• 125-lb (57-kg) capacity corrosion-resistant polyurethane hopper
• 13-in. (33-cm) pneumatic tires for easy rolling
• Enclosed gearbox (metal gears)
• Ergonomic dual handle featuring Accu-way™
• Accu-way even spread pattern adjustment
• Includes screen and cover

Accu-way is a trademark of Spyker Spreaders, Inc.

Hopper screen and throat opening

Hopper screens keep out debris and serve as chunk graters.

A stainless-steel hopper bottom plate/throat opening resists rust and corrosion, which extends the life of the spreader.

Spinner

Spinners are made of high-impact plastic that will not crack or break.

Dial-A-Matic rate control

The Dial-A-Matic rate control lets the operator fine-tune the rate application:

• Dial position locks and unlocks automatically.
• More than 80 settings provide an accurate application of materials.

Specifications

 

	125-lb (57-kg) Pull-Type Spreader	175-lb (79-kg) Pull-Type Spreader
Recommended market	Homeowner	Homeowner
Type	Tow-behind	Tow-behind
Bundle number	LP25353
Box capacity	125 lb (57 kg), 2.5 cu ft (0.07 m3)	175 lb (79 kg), 3.5 cu ft (0.1 m3)
Hopper size, in. (cm)	14.5x25.25x19.75 (36.8x64.1x50.2)	18.5x27.5x21.5 (47x69.9x54.6)
No-rust versatility
Hopper	Polyethylene	Polyethylene
Hopper screen	Aluminum	Aluminum
Hopper bottom plate	Stainless steel	Stainless steel
Throat opening, in. (cm)	0.81x2.75 (2.1x7)	0.81x2.75 (2.1x7)
Connecting hardware	Stainless steel	Stainless steel
Accurate application
Rate control	80-setting Dial-A-Matic knob	80-setting Dial-A-Matic knob
Rate gate	No-stick nylon	No-stick nylon
Rate gate linkage	Stainless steel	Stainless steel
Even dispersal
Spinner, in. (cm)	12 (366)	12 (366)
Spread pattern, ft (m)	10 to 12 (3.1 to 3.7) wide	10 to 12 (3.1 to 3.7) wide
Spread pattern equalizer	Accu-way™	Accu-way
Spinner shaft	Zinc-plated steel	Zinc-plated steel
Rotary agitator	Stainless steel	Stainless steel
Miscellaneous
Frame	Powder-coated gloss enamel, 16 ga, 0.6 in. (1.5 mm) 1.13-in. (2.86-cm) tubular steel	Powder-coated gloss enamel, 16 ga, 0.6 in. (1.5 mm), 1.25-in. (3.2-cm) tubular steel
Frame width, in. (cm)	18 (45.7)	18 (45.7)
Drive gears	Heavy-duty die-cast metal	Heavy-duty die-cast metal
Axle	0.63-in. (15.9-cm) solid steel, zinc plated	0.63-in. (15.9-cm) solid steel, zinc plated
Wheels/tires	13-in. x 5-in. (33-cm x 13-cm) pneumatic	13-in. x 5-in. (33-cm x 13-cm) pneumatic
Recommended travel speed	3.5 mph (5.6 km/h)	3.5 mph (5.6 km/h)
Warranty	One-year limited	One-year limited
Net weight, lb (kg)	29 (13.2)	34 (15.4)

 

Accu-way is a trademark of Spyker Spreaders, Inc.

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

125-lb Pull-Type Spin Spreader

Order number: LP25353

John Deere spin spreaders have features and a choice of sizes to satisfy many operators. They are a popular attachment for both homeowner and commercial operators who use them for even distribution of a variety of materials:

• Seed
• Fertilizer
• Insecticide
• Salt

All spreaders have rust-resistant stainless-steel or polyethylene hoppers as well as many stainless-steel components to ensure lasting appearance and long, trouble-free operation.

Features include:

• Positive on/off system (no cables)
• 175-lb (79.4-kg) capacity corrosion-resistant polyurethane hopper
• 13-in. (33-cm) pneumatic tires for easy rolling
• Fully enclosed gear box with metal gears for long life
• Accu-way even spread pattern adjustment
• Includes screen and cover

 

Hopper screen and throat opening

Hopper screens keep out debris and serve as chunk graters.

A stainless-steel hopper bottom plate/throat opening resists rust and corrosion, which extends the life of the spreader.

Spinner

Spinners are made of high-impact plastic that will not crack or break.

Dial-A-Matic rate control

The Dial-A-Matic rate control lets the operator fine-tune the rate application:

• Dial position locks and unlocks automatically.
• More than 80 settings provide an accurate application of materials.

Specifications

 

	125-lb (57-kg) Pull-Type Spreader	175-lb (79-kg) Pull-Type Spreader
Recommended market	Homeowner	Homeowner
Type	Tow-behind	Tow-behind
Bundle number	LP25353
Box capacity	125 lb (57 kg), 2.5 cu ft (0.07 m3)	175 lb (79 kg), 3.5 cu ft (0.1 m3)
Hopper size, in. (cm)	14.5x25.25x19.75 (36.8x64.1x50.2)	18.5x27.5x21.5 (47x69.9x54.6)
No-rust versatility
Hopper	Polyethylene	Polyethylene
Hopper screen	Aluminum	Aluminum
Hopper bottom plate	Stainless steel	Stainless steel
Throat opening, in. (cm)	0.81x2.75 (2.1x7)	0.81x2.75 (2.1x7)
Connecting hardware	Stainless steel	Stainless steel
Accurate application
Rate control	80-setting Dial-A-Matic knob	80-setting Dial-A-Matic knob
Rate gate	No-stick nylon	No-stick nylon
Rate gate linkage	Stainless steel	Stainless steel
Even dispersal
Spinner, in. (cm)	12 (366)	12 (366)
Spread pattern, ft (m)	10 to 12 (3.1 to 3.7) wide	10 to 12 (3.1 to 3.7) wide
Spread pattern equalizer	Accu-way™	Accu-way
Spinner shaft	Zinc-plated steel	Zinc-plated steel
Rotary agitator	Stainless steel	Stainless steel
Miscellaneous
Frame	Powder-coated gloss enamel, 16 ga, 0.6 in. (1.5 mm) 1.13-in. (2.86-cm) tubular steel	Powder-coated gloss enamel, 16 ga, 0.6 in. (1.5 mm), 1.25-in. (3.2-cm) tubular steel
Frame width, in. (cm)	18 (45.7)	18 (45.7)
Drive gears	Heavy-duty die-cast metal	Heavy-duty die-cast metal
Axle	0.63-in. (15.9-cm) solid steel, zinc plated	0.63-in. (15.9-cm) solid steel, zinc plated
Wheels/tires	13-in. x 5-in. (33-cm x 13-cm) pneumatic	13-in. x 5-in. (33-cm x 13-cm) pneumatic
Recommended travel speed	3.5 mph (5.6 km/h)	3.5 mph (5.6 km/h)
Warranty	One-year limited	One-year limited
Net weight, lb (kg)	29 (13.2)	34 (15.4)

Accu-way is a trademark of Spyker Spreaders, Inc.

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

175-lb Pull-Type Spin Spreader
Order number: LP25354

The 40-in. (102-cm) Aerator Spreader can do two jobs at once. It perforates the soil while the calibrated drop-spreader follows with seed, lime, or fertilizer. It can also be used to just aerate the lawn:

• 40-in. (102-cm) width, with up to 2 in. (5.1 cm) of penetration
• 132 steel-tine tips on 8-in. (20-cm) diameter tine stars
• Three-position, full-sized lift lever
• Direct spreader drive for consistent performance
• Adjustable flow control
• 100-lb (45-kg) spreader capacity
• 4.10/3.5-4 pneumatic tires for easy pulling
• 75-lb (34-kg) capacity weight tray

Quality design

John Deere tow-behind lawn care tools are compatible with all John Deere lawn and garden tractors, as well as competitive tractors.

This implement features legendary John Deere performance and quality.

Specifications 

Width	40 in. (101.6 cm)
Aerator depth	Up to 2 in. (5.1 cm), two positions
Spreader capacity	100 lb (45 kg)
Tines
Number of tips	132
Diameter	8 in. (20.3 cm)
Material	Steel
Lift adjuster	Manual
Wheels	4.10/3.5-4, pneumatic
Drive	Direct
Weight-tray capacity	100 lb (45 kg)

Vehicle compatibility and requirements

Requirements and/or recommendations: tow-behind equipment

1. Rear wheel weights are recommended for additional traction.
2. The 48-in. (122-cm) Tow-Behind Plug Aerator is not recommended for Select Series™ X300s, D100, LA100, 100, or L100 Series, 100 Series, LT, LTR, LX Lawn Tractors, EZtrak™ Mower or Residential ZTrak™ Mower.
3. The loaded weight of the utility cart not to exceed the weight of the vehicle and operator.
   The loaded weight of any attachment towed by an EZtrak or Residential ZTrak not to exceed 250 lb (113 kg).
4. For EZtraks and Residential ZTraks, only the 7P Utility Cart, 10P Utility Cart, or 42-in. (107-cm) Lawn Sweeper are recommended for towing.

Ordering information

Customers, please contact your local John Deere dealer for availability and pricing information.

40-in. (102-cm) Tow-Behind Aerator Spreader

Order number: LPAS40JD

Broadcasts fertilizer, weed control, grass seed or ice melter products while towing behind a riding lawn tractor. 130-lb (59-kg) polyethylene hopper resists rust and is easier to clean. Spread pattern will go up to 12 ft (31 cm) depending on speed and material. New direct rod control with easy to reach handle opens and closes the material gate. Heat treated steel gears with plastic enclosure are protected from corrosive material. Large knobby tread tires roll easily over turf.

 

Two-year warranty.

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

130-lb Pull-Type Spin Spreader
Order number: LP39087

This 175-lb (79-kg) pull-type broadcast spreader is designed for homeowner use:

• The polyethylene hopper will not dent or rust.
• All stainless-steel interior hardware, shaft, and agitator help to prevent corrosion.
• Large pneumatic turf tires ensure a positive drive and smooth operation.
• High-speed, 6:1 reduction glass-filled nylon gears provide the widest spread pattern at the slowest speeds.
• Fully enclosed gearbox eliminates downtime and maintenance.
• Autoflow feature stops the flow of materials - automatically - to prevent burns.
• Directional spread-pattern control feature provides positive shutoff along sidewalks and driveways.

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

175-lb (79-kg) Broadcast Spreader

Order number: LPBS36JD

The sun canopy provides protection from the sun's rays and gives the operator some cooling shade during the hot summer days.

Quick sun protection for 100 Series Tractors:

• Slips into CargO Mount™ system ports for quick installation
• Protects operator from the sun’s rays
• Tough woven polyester construction for strength and durability
• Designed to fit 100 Series Tractors

Ordering information
Please contact your local John Deere dealer for availability and pricing information.

Sun canopy
Order number: LP68122

 

The 40-in. (102-cm) Thatcherator can be used as a dethatcher or an aerator. It can also be used to prepare an area for seed:

• 40-in. (102-cm) width to cover ground fast
• 20 spring-loaded tines for maximum performance
• Three-position adjustment
• Weight tray to allow increased scratching power

An 8-in. (20-cm) extension is available to provide widths of 48 in. (122 cm) and 56 in. (142 cm). Add an extension to one end of the thatcherator to make it 48-in. (122-cm) wide and an extension to both ends for a 56-in. (142-cm) width.

Quality design

John Deere tow-behind lawn care tools are compatible with all John Deere lawn and garden tractors, as well as competitive tractors.

This implement features legendary John Deere performance and quality.

Specifications

 

Width	40 in. (101.6 cm)
Tines
Number	20, spring-loaded tips
Diameter	0.19 in. (0.5 cm)
Material	Steel
Weight tray capacity	100 lb (45 kg)
Lift adjuster	Three positions
Wheel
Size	8 in. (20.3 cm)
Tread	Rib
Material	Steel
Optional extension	8 in. (20.3 cm)

Requirements and/or recommendations:

1. Rear wheel weights are recommended for additional traction.
2. For use with the following John Deere vehicles and other lawn and garden tractors of similar size:
   • 100 Series Tractors
   • 200 Series Tractors
   • X300 Series Tractors
   • X500 Series Tractors
   • X700 Series Tractors

Ordering information

Contact a local John Deere dealer for availability and pricing information.

40-in. (102-cm) Tow-Behind Thatcherator

Order number: LPTA40JD

Protect your driving surface. TerraGrip Traction Belts offer enhanced traction on snow, mud, dirt, wet asphalt, and wet concrete surfaces. They will not scratch or chip concrete, asphalt, or aggregate drives or walkways. The proven reliability of the traditional steel chain attachment system is used and combined with the performance and durability of reinforced rubber slats. The rubber slats wrap around the tire so only rubber touches the driving surface. The result is aggressive traction without the risk of surface damage, that can happen with traditional chains.

Features:

• Rubber slats surround the tire and will not damage driveways or sidewalks.
• No steel touches the driving surface.
• No-tools installation utilizes a traditional steel chain attachment system.
• Traction is improved on all surfaces, especially loose material (snow, dirt, mud, sand, etc.).
• TerraGrip Traction Belts are approved for John Deere X300, X500 M-T, and X700 Series Tractors.

Additional information for 4-wheel-steer tractor models:

• X700 Series – requires wheel spacer sold separately
• X500 Series – requires wheel stop adjustment
• X300 Series – no additional requirements

Chains are recommended for extra traction when using attachments such as a snow blower or front blade.

One pair of chains is included in each bundle.

TY15959 tire chains - 20x8-8
NOTE: For LA105, LA115, LA125, D100, D105, D110, D120, D125, E100, E110, and E120 Tractors.

TY16200 tire chains - 20x10-8 (for some models), 20x10-10
NOTE: For LA135 SE, LA145, LA155, S240, X300/less deck, X300/38X, X300/42M, X300/42X, X300/48X, X300R, X304, and X324 Tractors.
NOTE: The rim diameter is larger for four-wheel steer tires, but does not affect chain requirements.

TY25229 tire chains - 20x10-8 (for some models), 22x9.5-12
NOTE: For LA165, LA175, D130, D140, D150, D155, D160, D170, E130, E140, E150, E160, E170, and E180 Tractors.

TY24327 tire chains - 22x11-10
NOTE: For X320, X340, and X360 Tractors.

TY15956 tire chains - 23x10.5-12
NOTE: For 190C Tractor.

TY26227 tire chains - 23x9.5-12, 24x9.5-12
NOTE: For X534 Tractor.

TY24328 tire chains - 24x12-12
NOTE: For X500, X520, X530, X540, and X590 Tractors. Also use with 26x10.5-12 tires on model year 2016- (SN 040,000-) X734 and X754.

TY25326 tire chains - 26x10.5-12
NOTE: For model year -2015 (SN -040,000). For X724, X734, X744, and X754 Tractors. Fits turf, bar, and heavy-duty all-purpose (HDAP) tire treads.

TY15958 tire chains - 26x12-12
NOTE: For X700, X710, X720, X730, X728, X738, X729, X739, X740, X750, X748, X758, and X749 Tractors. Will fit turf, bar, and HDAP tire treads. X729, X739, and X749 require BM22725 wheel spacer kit to provide clearance when installing tire chains.

The 42-in. (107-cm) Lawn Sweeper offers great performance and hauls an incredible 17 bu (599 L) of material. Its design gives superior brush-to-ground contact to prevent skipping and provide maximum performance for a clean path the first time through.

Features include:

• 42-in. (107-cm) clearing width
• 17-bu (599-L) capacity to make fast work of picking up material
• Convenient brush-height adjuster has eight positions for easy selection of the optimum sweeping height
• Hitch has seven positions to match up correctly with a variety of vehicles
• Large 12-in. (305-mm) x 3-in. (76-mm) wheels with bar tread have good gripping action to ensure positive brush rotation
• A unique storage feature allows the sweeper to collapse and be stored vertically to minimize storage space

Quality design

John Deere tow-behind lawn care tools are compatible with all John Deere lawn and garden tractors, as well as competitive tractors.

This implement features legendary John Deere performance and quality.

Specifications

 

Brush height	Sweeping conditions
Ground level to 1 in. (25 mm) above	Smooth surfaces - driveways, parking lots, and sidewalks
1 in. (25 mm) to 2 in. (50 mm)	Mowed lawns under normal conditions, or light leaves
2 in. (50 mm) to 3 in. (75 mm)	High grass, heavy leaves, or heavy grass clippings

 

 

Ordering information

Customers, please contact your local John Deere dealer for availability and pricing information.

42-in. (107-cm) Tow-Behind Lawn Sweeper
Order number: LPSTS42JD

The 44-in. (112-cm) Lawn Sweeper offers great performance and hauls an incredible 17 bu (599 L) of material. Its design gives superior brush-to-ground contact to prevent skipping and provide maximum performance for a clean path the first time through.

Features include:

• 44-in. (112-cm) clearing width
• 17-bu (599-L) capacity to make fast work of picking up material
• Convenient brush-height adjuster has eight positions for easy selection of the optimum sweeping height
• Hitch has seven positions to match up correctly with a variety of vehicles
• Large 12-in. (305-mm) x 3-in. (76-mm) wheels with bar tread have good gripping action to ensure positive brush rotation
• A unique storage feature allows the sweeper to collapse and be stored vertically to minimize storage space

Quality design

John Deere tow-behind lawn care tools are compatible with all John Deere lawn and garden tractors, as well as competitive tractors.

This implement features legendary John Deere performance and quality.

Specifications

 

Brush height	Sweeping conditions
Ground level to 1 in. (25 mm) above	Smooth surfaces - driveways, parking lots, and sidewalks
1 in. (25 mm) to 2 in. (50 mm)	Mowed lawns under normal conditions, or light leaves
2 in. (50 mm) to 3 in. (75 mm)	High grass, heavy leaves, or heavy grass clippings

 

 

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

44-in. (112-cm) Tow-Behind Lawn Sweeper
Order number: LP49038

This John Deere dethatcher kit has two rows of individually flexing tines that gently but effectively remove grass clippings, leaves, and other lawn debris from your lawn. The kit easily attaches to the front of John Deere's 42-in. (107-cm) Lawn Sweeper (LPSTS42JD) to add thatch pickup to the sweeper's cleaning abilities. The dethatcher does not need to be removed to resume regular sweeping use.

 

Ordering information

Customers, please contact your local John Deere dealer for availability and pricing information.

 

Dethatcher kit for sweeper

Order number: LP42108

The Multi Tool includes one platform and two separate attachments, saving space and money.

 

• Includes 40-in. (101.6-cm) weight tray - capable of holding up to 100 lb (45.4 kg) of weight
• Includes pre-assembled core aerator - reduces soil compaction allowing air, water, and fertilizer to the grass roots
• Includes dethatcher - removes unwanted debris from the top of the soil to allow nutrients to reach the grass roots
• Elongated handle - makes it easier to raise into transport or lower for use
• Spring assisted lever - makes changing the attachments quick and easy

John Deere has combined the best lawn tools into one package.

Two-year warranty.

 

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

 

Multi Tool

Order number: LP39089

The Lawn Roller packs down sod, seed, and mole ridges. Its tough polyethylene drum does not dent or rust. The drum's rounded ends do not gouge the lawn or make ruts:

• 36-in. (91-cm) wide polyethylene drum
• 390-lb (177-kg) weight for excellent leveling
• Rounded end caps to reduce gouging
• 42-U.S. gal. (159-L) capacity
• Long-lasting Nylatron® bearings

Quality design

John Deere tow-behind lawn care tools are compatible with all John Deere lawn and garden tractors, as well as competitive tractors.

This implement features legendary John Deere performance and quality.

Specifications

 

Width	36 in. (91 cm)
Roller
Size	36 in. x 18 in. (91 cm x 46 cm)
Capacity	42 U.S. gal. (159 L)
Weight (filled)	390 lb (177 kg)
Drum/end-cap material	High-density polyethylene (HDPE)
Bearings	Nylatron

 

Requirements and/or recommendations:

1. Rear wheel weights are recommended for additional traction.
2. For use with the following John Deere vehicles and other lawn and garden tractors of similar size:

• 100 Series Tractors
• 200 Series Tractors
• X300 Series Tractors
• X500 Series Tractors
• X700 Series Tractors

Ordering information

Contact a local John Deere dealer for availability and pricing information.

36-in. (91-cm) Tow-Behind Lawn Roller

Order number: LPPRT36JD

Nylatron is a trademark of Mitsubishi Chemical Advanced Materials Inc.

The 40-in. (102-cm) Plug Aerator removes plugs of soil up to 3-in. (7.6-cm) deep to allow penetration of air, water, and nutrients. It also helps relieve soil compaction:

• 40-in. (102-cm) width with up to 3 in. (7.6 cm) of penetration
• Three-position lift handle for 2-in. (5-cm) or 3-in. (7.6-cm) plug lengths
• 28 carbonized, 16-gauge, 0.06-in. (1.5-mm) steel, individually serviceable plugging tines
• 1-in. (2.5-cm) diameter high-carbon steel-tine shaft
• 4.10/3.50-4 pneumatic tires for easy pulling
• 175-lb (79-kg) capacity weight tray

Quality design

John Deere tow-behind lawn care tools are compatible with all John Deere lawn and garden tractors, as well as competitive tractors.

This implement features legendary John Deere performance and quality.

Specifications

 

Width	40 in. (101.6 cm)
Aerator depth	Up to 3 in. (7.6 cm)
Tines
Number of tips	28
Spacing	6 in. (15.2 cm) apart
Material	Carbonized, 16-gauge, 0.6-in. (1.5-mm) steel
Lift adjuster	Manual, three position
Wheels	4.10/3.5-4, pneumatic
Weight-tray capacity	175 lb (79.4 kg)

Vehicle compatibility and requirements

Requirements and/or recommendations:

1. Rear wheel weights are recommended for additional traction.
2. For use with the following John Deere vehicles and other lawn and garden tractors of similar size:

• 100 Series Tractors
• 200 Series Tractors
• X300 Series Tractors
• X500 Series Tractors
• X700 Series Tractors

Ordering information

Contact a local John Deere dealer for availability and pricing information.

40-in. (102-cm) Tow-Behind Plug Aerator

Order number: LPPA40JD

The 40-in. (102-cm) Spiker Aerator penetrates soil, allowing air, water, and nutrients to enter the lawn. It also relieves soil compaction:

• 40-in. (102-cm) width with up to 2 in. (5 cm) of penetration
• 10-in. (25-cm) diameter steel-tine stars
• 132 steel-tine tips on 11 spike wheels
• 3.5-in. (9-cm) spike-wheel spacing
• Full-sized lift lever
• 4.10/3.5-4 pneumatic tires for easy pulling
• 100-lb (45-kg) capacity weight tray 40-in. (102-cm) width with up to 3 in. (7.6 cm) of penetration

Quality design

John Deere tow-behind lawn care tools are compatible with all John Deere lawn and garden tractors, as well as competitive tractors.

This implement features legendary John Deere performance and quality.

Specifications

 

Width	40 in. (101.6 cm)
Aerator depth	Up to 2 in. (5.1 cm)
Tines
Number of tips	132
Diameter	10 in. (25.4 cm)
Spacing	3.5 in. (8.9 cm) apart
Material	Steel
Lift adjuster	Manual
Wheels	4.10/3.5-4, pneumatic
Weight tray capacity	100 lb (45 kg)

Requirements and/or recommendations:

1. Rear wheel weights are recommended for additional traction.
2. For use with the following John Deere vehicles and other lawn and garden tractors of similar size:
• 100 Series Tractors
• 200 Series Tractors
• X300 Series Tractors
• X500 Series Tractors
• X700 Series Tractors

Ordering information

Contact a local John Deere dealer for availability and pricing information.

40-in. (102-cm) Tow-Behind Spiker Aerator

Order number: LPSAT40JD

The roomy steel-frame cab shields the operator against snow, rain, sun, and wind to make snow removal a more pleasant experience.

The snow cab is compatible with all 100 Series and S240 Tractors:

• D100, D105, D110, D120, D125, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180, and S240

Roomy steel frame cab shields against snow, rain, sun and wind.

Key features include:

• Double-zippered access hole for control maneuverability
• Interior mesh pockets to hold accessories
• Super-clear vinyl windows are cold-crack tested to -4°F (-20°C)
• Internal non-scratch magnets to ensure a custom fit - no tool necessary
• Zippered doors have a snap-lock system to hold them open
• Rear locking panel holds enclosure tight against tractor frame
• Assembles and installs with standard hand tools

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

Snow cab

Order number: LP68121

A durable cast-iron weight can be mounted to each front wheel.

These weights are recommended for use when operating on slopes, especially when the tractor is equipped with a rear grass bagger or other rear-mounted equipment.

Each weight requires BM17978 mounting hardware.

The 42-lb (19-kg) Quik-Tatch can be used to counterbalance a heavy front or rear attachment and/or provide greater stability, especially when operating on hills.

This weight is constructed of cast iron and weighs approximately 42 lb (19 kg).

Some vehicles have built-in front and/or rear weight brackets to hang the weights on; others require a weight bracket that must be ordered separately.

X400/X500 Heavy-Duty Garden Tractors and X700 Series Tractors require the following parts when weights are installed on the front of the tractor:

• One  M147986 weight retaining rod (Parts)
• Two  M40461 spring clip (Parts)

The rear suitcase weight provides extra ballast that is needed to reduce wheel slippage and increase snow-removal capability.

The rear weight bracket provides a tractor-mounted bracket for hanging two weights:

• BG20627 replaces BG20022 and BG20499 rear weight brackets.
• Clearance is provided for the carbon canister that is required on tractors sold in California.
• BG20627 can be used in all applications where BG20022 and BG20499 were used.

Hardware is required for installing each front-wheel weight.

Requirements:

• Mounting may require drilling two holes in the wheel rim.
• BM17978 mounting hardware kit is required for each weight.

NOTE: Front-wheel weights are not available for special edition tractors because the styled front-wheel design does not have appropriate holes for mounting the wheel weights and no adapter is available.